Hi,
This is a bit more of a typo report.
In the Debug Logger doc page , app_trace_init() is supposed to return an int but in its function declaration it's said to return...
Hello All,
I'm trying to build a receiving unit using the nRF24L01+ and PIC16F628A. Im using an nRF24L01+ and RaspberryPi as my TX unit which i managed to get working ...
Hi,
We have a device using the S110 v6.0.0 softdevice and the SDK v5.2.0.
We started working from the Proximity application available in the sdk.
Is it possible to...
Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hi,
Sorry if the answer is obvious but I'm not getting it :-)
I looked at ble_app_uart, more specifically the uart_event_handle function and its interactions with app_uart_fifo...
I want to access an SPI-only sensor device from a Blend Micro.
There is a need to avoid collisions between the two uses of the SPI port for the sensor and the nRF chip...
I just made it to upload the example to the device. I'm new into firmware development btw.
I changed the timeout so the beacon will stop advertising after 120 seconds but...
Hello, I have implemented the code below for my project
based on switching central and peripheral role in S130.
The code works fine on the Devkit PCA10028 but on porting...
In compatibility matrix it is shown that s110 v 7.3.0 is compatible with nrf51422 when using SDK 7.x.x. But when I downloaded s110 v7.3.0 in its name and specification documents...
I tried to build the example project "ble_app_uart" bundled with nRF5 SDK (nRF5_SDK_11.0.0_89a8197) within the MDK-Lite V5.18K. It failed and I got the following messages...
Hi!
I am attempting to flash sdk11 examples onto a QFAB board compiled using arm-gcc over JLINK SWD p20 via the NRF-51DK.
While running make flash, the nrfjprog command...
Hello I found example for dual bank bootloader ("examples\dfu\bootloader\pca10040\dual_bank_ble_s132"). And it works well.
Do you plan also to add a SINGLE bank boot-loader...
hi all,
I am using SDK version 8.
i want to make button as ON and off switch.
REQUIREMENT:
When button is pressed counter should keep on incrementing when i released...
Hello,
I would like to simulate the spreading of a disease using the nrf51822 beacons. My question is if my envisioned project is possible as I'm completly new to nrf51822...
I would need to change a timer into single shot mode. My code is as follows:
static const nrf_drv_timer_t m_timer = NRF_DRV_TIMER_INSTANCE(MY_SAMPLE_TIMER);
nrf_drv_timer_init...
using S130, SDK11,
CANNOT work the two heart rate sensors which have the different deivce name ?
when it connected the heart rate sensor A and eveything is OK.
but...
Hello,
I want to use nRF52832 at 2V. But I am not sure what would be the current consumption of radio during transmission and reception with DCDC regulator on. In datasheet...
