Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
Hi. i'm using PCA10028, SDK10.0.0, S130.
I want to check RF characteristics.
nRf51 should make RF Tx continuously.
I think there is example source code for that.
Which...
The function dm_ble_evt_handler has codes like this.
void dm_ble_evt_handler(ble_evt_t * p_ble_evt){ // from device_manager_peripheral.c
switch (p_ble_evt->header...
Hello,
I have develop and app to send BLE Advertisement packet in Android. But what I found out is my device has Android Lollipop but it does not have peripheral mode turned...
I am using the nRF52 Preview board, PCA 10036. I need to provide a high-frequency clock signal to a peripheral. Anything between 1 and 4 MHz will work. However, I don't need...
I currently call nrfjprog twice to flash the softdevice hex and then the app hex separately. But as I am using two nrfjprog calls, I am unable to set --rbp ALL with the second...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hi there,
Currently, I am working on a project which uses iphone(or other IOS device) as a central, and nrf51822 as peripheral.
Basically, the concept is that peripheral...
itg3200.rar hello there i have interfaced itg3200 with nrf51 dk. but now i want to see it on oscilloscope. can you help me?? i have put my scope's screen shot and code here...
HI all,
We've recently moved to SDK 11.0 and it certainly has not been a painless migration, especially when using GCC.
Setup: GCC 5.2.1 on Linux Mint with nrf51 xxAA...
Hi, I'm wonder it is possible to stream video using nRF52x family? I know that chipset isn't designed to this purpose, but I'm only wonder about that.
Thanks
Robert
Hi,
I've started using the nRF5 11.0.0 (89a8197) SDK on a board that does not include an external low-frequency CLK source.
When using the nRF52 0.9.2 SDK, we were recommended...
I want to reserve a section of memory, FLASH, that will hold static, read only, product data. My application makes use of the following parts of the Nordic ecosystem.
...
I would like to carry out communication with a plurality of peripheral using a central multi-link function.
When performing the communication via the relay unit, the communication...
Hi ,
I'm intrested in using the BLE UART apllication provided by Nordic for the nRF51 422 developpement kit and I have a little question to ask and please forgive its simplicity...
Environment is a PCA10040 v1.1.0, measuring current with a Rigol DS1104B over a 10 Ohm resistor.
I'm using the ble_pwr_profiling example from nRF5 SDK v11. I've programmed...
