Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hi there,
Can you please tell if with 'Sniffer' I can track down and see all images shared with my pc's webcam?
If so, how can i do that?
Thank you so much for your...
Hi all,
I am moving from Keil into SES, and one of the things I am not being able to find is how to do the __PACKED pragma.
I see in SES that:
#elif defined ( __GNUC__...
I'm trying to use the SEGGER debugger with one of the OpenThread examples for the nRF52840. When I click on the "Go" button, it asks for the location of the source files for...
I think I found a bug in ble_dfu_bonded.c.
In ble_dfu_buttonless_bootloader_start_prepare() there is a call to gscm_local_database_has_changed(). The problem is that this...
Hi,
How do i enable Gyroscope Support in Smart Remote FW v1.2?
When I enable this in the sr3_config_*.h file, setting "CONFIG_GYRO_ENABLED 1", I get an error stating:...
Hello,
I have moved my project from SES 3.34a to 3.40 and I see a new error at compilation.
When compiling the file nrf_pwr_mgmt.c’, I have the errors below :
unrecognizable...
While attempting to run the following code from a MESH example in IAR, the program gets stuck. It only seems to be calling button_event_handler continuously, as if the interrupt...
Hello,
I have been looking to program this IC, connecting via SWD with no luck. I can connect to the target but for some reason once i try to perform erase programming...
Hi!
What's the difference between UART_TX_BUF_SIZE and BLE_NUS_MAX_DATA_LEN in case of ble_app_uart example?
As I have noticed BLE_NUS_MAX_DATA_LEN determines maximum...
Hi,
I have a question about DFU mesh, I'm working on light switch demo and I combined light_switch_server with DFU exam ple in order to only u pdate server node with light_switch_server...
Very newbie question, so, sorry.
I am starting to use SES and the Find and Replace works fine in the same document, but if I do it for Replace in Files (Ctrl-Alt-F), it...
Hi,
I am using SDK14.2 with softdevice v5.1.0. I have recently ported my application from SDK12.2.
When I run my application with the softdevice it works fine. But when...
Hi everyone,
I'm in trouble with the stdlib of Keil SDK , which is nRF5_SDK_15.0.0_a53641a, while compliing.
The code what I add in the demo project causes Undefined...
Hello, i'm trying to updade my firmaware using the DFU. I manage to do it with nRF Connect and nrfutil but i'm trying to a custom central to flash the software without any...
