Hi, when I am trying to set up channel sounding, I am looking for the best parameters for CS configuration. The main problem I have is that even with slow movement (1 km/h...
Dear sir,
I'm using the sample application "channel_sounding_ras_initiator" to performing the evaluation. Here are my test environment: - Developement kit: nRF45L151 - Tool...
Hello,
I previously used DECT NR+ modem firmware mfw-nr+_nrf91x1_1.0.2 on nRF9151 DK Development kit and moved on using the new modem firmware mfw-nr+_nrf91x1_1.1.0.
But...
Hello.
This may be a basic question, but please let me know. I am using nRF54L15-DK and nRF Connect SDK v3.0.2.
Is the 32MHz crystal running when the nRF54L15 program...
hi everybody: This is my first time developing an nRF chip and also my first time using VSCode After installing nRF tools and fast (3.0.0), I found that I did not see the...
Hi there,
I am using an NRF54L15 custom board and am trying to set up a functionality using DPPI + PPIB. using a single in (1 event) and single out (1 task). I have two...
Hi,
I'm trying to get the debugger to work on my target board. I created the attached simple program to eliminate complexity.
The debugger starts, but it starts running...
Hi Noridic team,
I have enabled Matter over Thread on the nRF5340. In this setup, I'm planning to reduce the TX power by setting CONFIG_OPENTHREAD_DEFAULT_TX_POWER=0. Apart...
Hi,
I have a question about FOTA jobs with queued and failed devices.
Let's say I am managing a group of 10 cellular devices (nRF9151) through the nRF Cloud UI. I create...
Good day,
I am currently working on a project involving the nRF54 series and would like to inquire about support for the NEC infrared (IR) communication protocol. Specifically...
I'm testing my code based on nrf5SDK v17.0.0 with nrf52832 board.
By nrf connect application,I can see the broadcast packet from my board.It looks something like this. ...
Hi I'm working with nrf5340 dk. I have a serial app (on windows) that is doing serial write continuously to the nrf5340 dk but it is not capturing all the data that I'm sending...
Context
We are working on a project that implies advertising and scanning extended advertised packets.
details :
NRF52840
Zephyr SDK 17.0
Zephyr 4.0.99
NRF SDK...
I am trying to port code I developed on the NRF52 DK to a MDBT42Q-512KV2 BLE module from Raytac I purchased from Digikey and am running into problems.
I developed all the...
Hello,
I'm working with a custom board, using an nRF5340 (NCS v2.7.0 but also tested with version 2.9.0) and a W5500. I'm trying to run the DHCPv4 client test just to verify...
Dear Nordic company,
I have question connected with nrf9151 chip. I know, that this chip contains two parts, ARM core and modem.
I am trying to understand of Serial...
Is there a sample app that uses the Zephyr Light CTL Bluetooth Mesh model? I've tried to add that model to the light_ctrl sample app, but get a crash during configuration...
Hi,
The nRF Connect Extension on my Windows VS code doesn't load altogether:
I uninstalled VS code - including all it's settings/extensions etc using this post's suggestion...
Hi,
I can build and program the broadcast_source sample application using the Python script:
This runs fine and broadcasts as expected. However, I cannot get the application...
Hi, I'm working with the nRF9151DK and Zephyr RTOS (v3.7.99 / NCS 2.9.1) . I’ve configured UART1 to send and receive data via GPIO pins:
TX: pin 8 (P0.08)
RX:...
Hi everyone, I am working with the new nRF54L15 and have connected UART21 to pins 2.07-2.08, which are capable of handling both Trace data and UARTE. However, I am encountering...
