Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I have downloaded SDK software nRF5_SDK_15.2.0_9412b96. I am using segger studio as my IDE on windows.
I tried compiling the Example code for SAADC. There were no errors...
Hi, On SDK12.3 when using sd_flash_write at any memory location causes the device to halt and restart. On SDK11 I've been using flash_word_write and flash_page_erase using...
Hi I am using a nrf52832 board with a BMI160 sensor. I am trying to sample Accel and Gyro at 1600hz using a timer. The timer timeout is set at 20 ticks (32768/1600) @32768...
Dear Sir/Madam,
currently I am using SMK BLE module - BTS04, blank type (QDID 90744) and we have already acquired the Nordic Development Kit nRF52, Rev.1.2.4 date 2018.23...
morning guys ;
I wanna create a bluetooth pan using raspberry pi and beacon nrf51822 using ipv4 , i don't have problem with the raspebrry it works well and it shares the...
12.3 sdk
i have error when compile this project ''.\_build\nrf52840_xxaa.axf: Error: L6218E: Undefined symbol SEGGER_RTT_printf (referred from main.o).'"
this error how...
Hi I trying to interface Accelerometer sensor LSM6DS3 to NRF52832 DK.
whether I need to change board configuration or any pin configuration.
Pin configuration that i have...
The reset button doesn't seem to work on two of my PCA10056 1.0.0 development kits, but works on two others, and works on some earlier versions.
I tested by running the...
It was working a few times, then suddenly I started to get these errors, which I only got previously when not running as root (perhaps because it did not have permission to...
Hi,
I am trying to process data from MPU9250 in MATLAB and I have converted " .mat " file to " .hex " file using Embedded Coder . Can someone tell me if that " .hex " file...
(1) I am using GNU C++ to develop my application with nRF5 SDK. I found the STATIC_ASSERT_SIMPLE and STATIC_ASSERT_MSG macros defined in app_util.h are not working with C...
When running the light_switch_provisioner example built on my machine, it crashes on an assert in entry_validation() in mesh_config.c:
app_error_weak.c, 95, Mesh assert...
Hi,
I've a Raspberry Pi, Node-RED, with a Thingy connected. I get a message payload, looking like this:
{"uuid":"dfb561bb7d69","characteristics":{"2a00":[84,104,105...
