When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi,
want to try out the nRF52x Family, so will buy the DK board, which IDE is recommended? I am familar with VS Studio or Atmel Studio 7, so is there something like that...
Hi:
I want to capture the parameter of a digital wave like this, I want to get every 't' value. The wave is same in a period of time, but the 51822 capture value of 't' is...
SDK: 10.0.0
Softdevice: s110_nrf51_8.0.0
I'm working on migrating our application from SDK v9 to v10. I'm getting a softdevice assertion failure in src/rem.c line 1371...
Hi,
Can I use power profiler kit for current measurement of nRF52840 SoC?
If yes is there any hardware and software revision version(s) for power profiler kit?
Please...
I created a BLE Peripheral to read the light intensity, the purpose is connected to the iPhone device to read the update value in the BLE_NRF_52 device.
For the calibration...
Hi,
I checked this thread https://devzone.nordicsemi.com/f/nordic-q-a/24611/how-to-change-the-name-of-bootloader-s-dfutarg which suggests to modify the macro but I would...
Hello
for my project at the university I have to implement a bluetooth mesh network using 4 nordic thingys:52 and one nRF52DK(only for programming purposes, not part of...
Hi All!
I use Example Project from SDK: "examples\peripheral\usbd\" as reference to implement my HID device simple protocol (EP1IN / EP1OUT 64bytes)
The Question is how...
I am working with the BL652 Module from Laird, and with Keil 5, using a ST Link SWD programmer clone.
I am using the ble_app_uart_timer_driven_scan_mode from the ADC examples...
Hi, I am developing an IoT sensor (peripheral device) using SDK v11.
On my sensor, I have defined an advertising packet that broadcasts the complete local name and a scan...
I'm in the process of porting my application from SoftDevice S132 v4.0.2 / SDK v13.0.0 to SoftDevice S132 v6.0.0 / SDK v15.0.0. I noticed that the define for BLE_GAP_TIMEOUT_SRC_ADVERTISING...
Hello,
I'm attempting to use a high-limit reached event from the SAADC to trigger the clearing of a GPIO. My wish is to disable this GPIO with the lowest possible latency...
I used SDK 13.x to create a custom profile with services for nRF52832 with BLE 4.2
If I go to a nrf52840 with BLE 5.x SDK, can I use the exact same code, or do I have to...
