Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
Apart from pressing Button 4 or adding a DFU service to current running application. Is there any way to enter DFU mode from application?
Is it possible with nrfutil to...
Is there any tutorial or good example for I2C communication using TWI? I already saw the examples for TWI, but I don't find them very intuitive to change for I2C.
I'm trying...
After updating an application on nRF51822 chip with a new application which has new Characteristic UUID via BLE, iOS app cannot detect the new Characteristic UUID.
I know...
Hi to everyone,
I'm trying to use the CMD Mode of my Sniffer but I have different problems. First of all, when I switch to the CMD Mode the red LED didn't blink (it doesn...
`Hi Guys,
I have some sensor data of 20 bytes at each measurement at different period stored in EEPROM. Now i have to transmit all data over BLE continously.
example ...
I have a laser distance sensor module. I want to connect this module with my nRF52 DK(PCA10040). The module communicates over UART:
Supply (2.8V-3.2V VDC) connected...
I want to purchase a BLE development kit. My current preference is nRF51 because there are more nRF51422 BLE modules in the market.
www.nordicsemi.com/.../3rd-Party-Bluetooth...
hi,
I'm using ble central example using S130 softdevice . It works fine without editing anything. In my application, I dont want to put the nrf51822 to System On low power...
We are seeing random connections on our peripheral devices and we have tracked them to a Mac Pro. The computer has never been paired with any BLE devices so we have no idea...
hi
in this pic CODE_R1_BASE is 0x16000 and amount is 88kB
how its size in keil is 0x29000
if i calculate ram we have 8kB
8*1024 = 8192 that is in hex 0x2000 its...
How can I advertise a custom service and the Device Information Service?
I tried the following, but only my custom service is visible in the Nordic Master Control panel...
Hi there,
I'm issuing a STOPRX at a specific time but I'm noticing that more bytes are being put into the buffer from after the STOPRX was issued.
Is there a way to...
Since I've migrated to SDK 10 and updated all my toolchains I've noticed that when I debug on Eclipse, when I run my code nothing happens properly. However if I pause and...
There are various examples in the keil microvision examples for DTM.
The list is below. Is there a difference between these examples?
Which one should we use if our design...
Currently the default for the SPI0 chip select is active low. I would like to change it to active high. Can I do this?
If not can I just have the SPI chip select on a pin...
