Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
I am using a eeprep tool which can only be used with command prompt. I am struggling with it.
Here is the format to use eeprep tool :-
usage: eeprep [options] <infile...
Hi,
I'm trying to debug my program after trying out the DFU example (specifically dfu/bootloader/pca10040/dual_bank_serial_s132).
Using my Segger J-Link, I run 'erase...
Hi,
I'm using the nRF52832 QFAAB0 with IAR Embedded Workbench IDE.
I have "nRF5x_MDK_8_5_0_IAR.msi" installed.
Inside IAR i have the device selected as "NordicSemi...
I'm trying to write a small program in mbed that relays incoming UART BLE messages to the USB UART.
What is the proper way to setup notifications?
Right now, if I call ble...
Hi,
Warning: This might be a bit of a rant.
Is there going to be an effort made to make more of the nRF52 hardware drivers compatible with FreeRTOS?
Hopefully constructive...
Hello,
I am starting from ble_app_multilink_central example in SDK11.
Per the comment, when updating the number of central links, RAM setting should also be updated...
Hi,
i am using pca10028 with S130v2
We'd like to use a couple of services as we have to deal with a number of external interfaces.
Sadly we cannot get more than 4 services...
Hi there,
I'd like the ability to hold some data locally then resynchronize once the central reconnects.
Are there any example projects that demo this?
What is the...
Hi,
i am not able to send (write characteristic) from android at a higher transfer-rate than 2.3 kbit/second.
With another Bluetooth LE peripheral i get more than 100kbit...
Hi all, i have a nrf51 Development kit and a nrf51822 smart beacon kit and I want to read them in Matlab using the bluetooth receiver of my laptop. I used the instrumentation...
hi all
i try to write in volatile memory but after the second (the first is ok) writing the nrf8001 response me with 0x84 0x08 0x81 -> Internal Error
i don't know why
please...
Hi, apologies for my ignorance but I'm confused by something. I'm looking to add a PA and was thinking of using the RFAxis RFX2401C like many of those nRF24L01+, PA and LNA...
Hi All,
Please tell is ble mesh is it work for nrf51822 EK, the code is taken from this link: github.com/.../nRF51-ble-bcast-mesh . the code provided in this link, is tested...
We have made a bare minimum prototype with nrf51422 QFN chip following the reference schematic for internal LDO setup in 11.5.1 section of nrf51422_PS_v3.1. It is built on...
Hi,
Am using NRF52 S132 softdevice,
I have a use case like when I press a button , I should turn off BLE. So I enabled an interrupt for button. Whenever this button is pressed...
Hi,
i am using nrf51822 to develop our product. I'll try to describe more details to make you understand more clearly.
STEPS:
While testing my project, I had...
