Hi Guys,
I know this is more for software issues. But I was curious as to where I can find trusted case providers/makers for the nrf51822 Beacon. Can anyone from the community...
Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hi, I am importing a bootloader project that uses softdevice s110 and NRF51822 from Keil to Segger Embedded Studio. I have got all kind of errors during the process and I...
Hi Team,
In BLE5,
1) Can we connect a peripheral device to multiple central device?
2) Is it possible to check if connecton fails with any central device in perpheral...
I'm trying to put thingy_sdk_v2.1.0 and 10 nrf52832 boards. I'm compiling "ble_app_thingee_s132_pca20020.emProject". I don't know why it's always an error. How do I demonstrate...
Hi,
I'm using nRF52832 and SDK 15 and IDE im using is Segger studio.
i have ported the uart code into Ble_app_multilink_central.When i debug the code it is getting stuck...
Looking for an example on how to advertise for 10 seconds then go into sd_power_system_off. Trying this by using ble_app_template (s112, ses, sdk15.0, custom, 1 led, 1 rgb...
Hi nordic
I bought the nrf52840 board so I'm developing.
I want to use the this kind of LIR2032 coin cell 3.6v ( www.amazon.com/.../B074VX8ZJF )
I measured power of...
Hello, I'm experiencing frequent endless loops at 0x16cbc with s132_nrf52_3.0.0 softdevice and SDK 12.3 on a custom board with Aconno NRF52832 module. I'm using SAADC and...
Please can you help me with this fairly straight-forward technical query for a customer new to BLE.
Please can you advise which is the best way to structure the link in...
Hello,
I am currently working on the development related to RSSI of beacon using nRF51_SDK_9.0.0_2e23562(SDK). The beacons I’m using are developed with this SDK as well...
Hi guys!
I want to select NRF52840 as my target platform. Is it possible to start software developing on 52832 (for which I have devkit) and then seamlessly move my code...
Hello, I want to do a project with Segger Embeded Studio using the nRF52840 with the SDK_Mesh I have 2 nRF52840 cards and I want to transmit data to a mobile phone using a...
i compiled the ble_uart_app project it got downloaded in to the NRF51DK but the bluetooth is not getting turned on ,usually the output of this example is LED has to be turned...
Thanks for your support folks!
I am trying to read some bytes I have wrote in a MX25R8035F. From the datasheet, if you send 0x03 (READ) + 3 Byte address, then the memory...
Hi,
We want to receive the data in laptop over the BLE like nRF UART mobile APP.
we sending and receiving data in Mobile app but we can't get the app for desktop.
we...
Hi,
1-I did some test for nrf51422 (SDK12.3 + soft device S130) power consumption. result as below:
-system on sleep mode( without UART and BLE Advertise ):90uA
-system...
