Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
hi support team,
DTM is not able to build thingy53, do we have any support for this board? or any instructions for it?
radio_test is also not able to build thing53.
...
Hi everybody.
I'm developing my own board based on nRF52840 SoC. I'm using nRF Connect SDK 2.6.1. I need to log the environment events by date & time details on QSPI using...
Hi!
We are developing home automation light control mesh products.
We use nrf52832 DK (PCA10040), with nRF Connect SDK Toolchain v2.7.0 and nRF Connect SDK v2.6.1
We...
hi,
After upgrading mcuboot from NCS 2.6.1 to NCS 2.9.0, the upgrade file is downloaded, and the device restarts and runs normally. The mcuboot version number and active...
I have a nRF54L15-PDK kit. I also have the latest v2.9.1 SDK and toolchains installed using the VSCode plugin (also latest).
I use the plugin to create a new application...
I am new to designing with Nordic microcontrollers. I am at the point in my design where I am laying out connections to the microcontroller and setting up which pins will...
when I tried to add a device to nrf cloud, I am getting an error message 40101
My device is nrf9151dk with IMEI 359404230049133 and HWID 374155 I believe I might have registered...
I am exploring the possibility of using ncs v2.8.0 for Mesh with Coded PHY on the nRF52840dk/ nRF52840 board . I know this is not officially supported.
I started with the...
Dear,
I’m using nRF Connect SDK 2.7.0 with BLE Mesh and wondering how to adjust the TX power dynamically. When setting the TX power using a predefined option like CONFIG_BT_CTLR_TX_PWR_PLUS_8...
NCS 2.7.0
nrf52840
I'm currently porting software that was originally developed for nrf52832 on NRF5 SDK to run on Zephyr. I am currently on a deadline to delivery a prototype...
I've tried to follow the exercises from the Bluetooth Low Energy Fundamentals course. When I try to run the solution for lesson 3 exercise 2 I get the following error messagen...
Hello,
I have some previous code that ran using BT mesh. I then updated SDK's to 2.9.0 and I am now having issues provisioning devices. I am using the BT Mesh Provisioning...
Hi,
We are currently developing an application where we use a nrf52811. Currently i am working on integrating the BLE-Stack as this is the last part missing.
I am constantly...
Hello -
I am working through the DevAcademy - nRF Connect SDK Intermediate lessons. I have reached Lesson 7 Exercise 1, found here - https://academy.nordicsemi.com/courses...
Hi Team,
For my project, I am using nRF 5340 board and using the Zephyr SDK for development. I need to read and write data from/to an external QSPI EEPROM used ( MP95P08...
