I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi,
I'm trying to implement the buttonless DFU service example for SDK 12.3.0 into my own project, but when I call ble_dfu_init my compiled .hex file becomes 10 kb larger...
Hi,
I am working on SDK-14.2 and after execution of code i get this two error mention below.
sd_ble_cfg_set() returned : Unknown issue when attempting to set BLE_CONN_CFG_GAP...
Hi I have implemented a controller device using nRF52832. The controller device is installed in an industrial control box where it is used to control relays that subsequently...
Hi,
This question might be a little bit off, but not to far off for this forum I hope.
I am considering the nRF52840 Dongle to gain a better understanding of a issue...
Hi guys,
I need to get MAC address of my device and put it into characteristic? Is it possible? And maybe someone can tell how to implement this?
Regards,
Konstant...
Hi:
I use heart_rate_collector project in pc-ble-driver ( https://github.com/NordicSemiconductor/pc-ble-driver/blob/master/examples/heart_rate_collector/main.c )to connect...
Hello,
we are studying component base for development Wireless Hearing Aid device.
trying to understand limitations and capabilities of your nRF51822 SoC.
1. Can...
When test the current in the WFE state.
If not use the DMA, the current is not exceed 0.1mA. And when have used the DMA, the comsumption is very high , the current is about...
Hi,
We have a custom board with nRF52832 QFABB0 chip. High frequency crystal used is 32MHz (Part No: ECS-320-8-37CKM ) with two 12pF load capacitors (Part No: 80-CBR04C120F5G...
Hi All,
As "Mesh beaconing example" work as a advertiser and at a same time it scan beacon also.
I just want to use only beacon scanning functionality in this application...
Hi
I have moved an application from Softdevice 130 V5.1 (with SDK 14.2) to Softdevice 130 V6.0 (with SDK 15) both using keil.
My BLE peripheral device name is Nordic1234...
we are using NRF52832 for a project design, I am a bit of afraid of BQB certification, I think add a such like Johanson 2450FM070029 ceramic filter in front of antenna, (...
Hi guys,
I will begin the bluetooth mesh structure part of my project. I looked at this topic to learn what I have to do for creating a mesh project at KEIL. That guide...
