Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hi,
I'm trying to implement the buttonless DFU service example for SDK 12.3.0 into my own project, but when I call ble_dfu_init my compiled .hex file becomes 10 kb larger...
Hi,
I am working on SDK-14.2 and after execution of code i get this two error mention below.
sd_ble_cfg_set() returned : Unknown issue when attempting to set BLE_CONN_CFG_GAP...
Hi I have implemented a controller device using nRF52832. The controller device is installed in an industrial control box where it is used to control relays that subsequently...
Hi,
This question might be a little bit off, but not to far off for this forum I hope.
I am considering the nRF52840 Dongle to gain a better understanding of a issue...
Hi guys,
I need to get MAC address of my device and put it into characteristic? Is it possible? And maybe someone can tell how to implement this?
Regards,
Konstant...
Hi:
I use heart_rate_collector project in pc-ble-driver ( https://github.com/NordicSemiconductor/pc-ble-driver/blob/master/examples/heart_rate_collector/main.c )to connect...
Hello,
we are studying component base for development Wireless Hearing Aid device.
trying to understand limitations and capabilities of your nRF51822 SoC.
1. Can...
When test the current in the WFE state.
If not use the DMA, the current is not exceed 0.1mA. And when have used the DMA, the comsumption is very high , the current is about...
Hi,
We have a custom board with nRF52832 QFABB0 chip. High frequency crystal used is 32MHz (Part No: ECS-320-8-37CKM ) with two 12pF load capacitors (Part No: 80-CBR04C120F5G...
Hi All,
As "Mesh beaconing example" work as a advertiser and at a same time it scan beacon also.
I just want to use only beacon scanning functionality in this application...
Hi
I have moved an application from Softdevice 130 V5.1 (with SDK 14.2) to Softdevice 130 V6.0 (with SDK 15) both using keil.
My BLE peripheral device name is Nordic1234...
we are using NRF52832 for a project design, I am a bit of afraid of BQB certification, I think add a such like Johanson 2450FM070029 ceramic filter in front of antenna, (...
Hi guys,
I will begin the bluetooth mesh structure part of my project. I looked at this topic to learn what I have to do for creating a mesh project at KEIL. That guide...
