Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
I have nRF8001-DK and Arduino Uno. ble_uart_project_template from nRF8001 SDK for Arduino (Bluetooth_low_energy_for_Arduino_0_5_0_0_RC2) was used. It was used with Master...
Hello,
i create a custom profile with two services and with 30 characteristics. The first service has 29 characteristics. Up to this point everything is ok, but when I...
Hello, i would like to know if its possible to use your SDK tools (S110 Soft Device, nRF51 SDK) without your evaluation/development kit.
Since RFduino has a RF51822 chip...
Hi, I try to create a iBeacon tag with NRF51822 for Apple device, but it seems not to work, yesterday I update the newest SDK, I found the ANCS was added, so Nordic also can...
Hi,
i have a big Problem, if i debug my code i get in some cases in register 3 the value 0xDEADBEEF and after that the device doesn't work any longer in a correct way....
Hi
I can use the duf_dual_bank_ble to do the OTA,but I donn't know how to use the dfu_single_bank_hci to do the OTA.Could you give me some
advice about it?Thanks.
Hi.
I have a problem with writing value to gatts attribute when device is in connection mode. In my application I want to check if the parameter writing by the client to...
Hi,
I have downloaded the new version of SDK (v.5.0) today and just tried your experimental ble_app_ancs (no modifications) but it seems it asserts with error_code=0xB...
Hi,
I need to know when to use the write_wo_resp property for a characteristics, and what is the difference between write and write_wo_resp property of a characteristics...
I've read a post from Marc Nicholas about the attempt to port the entire gcc toolchain under Xcode on Mac OS X.
As I wrote in another post, I've the entire gcc toolchain...
I'm getting started with this evaluation kit by working through the user guide and almost made it through the Blinky example before I ran into trouble.
After compiling...
We have some hardware versions of the Nrf51822: build BA, CA.
Is the new S110 v6.0.0 softdevice compatible with these hardware versions?
If it is not compatible, wich...
Hi.
Using 51822 with BLE stack, I was faced with the problem of low transfer rates (5kb) on my android device (phone). It is very slow.
Can work 51822 with standart...
Can I initial like below to generate 2 opposition PWM waves on 2Pins？
/* Configure PPI channel 0 to toggle PWM_OUTPUT_PIN on every Timer 2 COMPARE[0] match. */
NRF_PPI...
Hi All,
Now I'm doing the OTA and I can use the nRF51822 DK and Master Control Pannel to complete the firmware update.I have a idear but I meet some problem.
I use the...
