I am running Windows 7 Pro SP 1 64 bit and have gong through the tools installation procedure, in particular running nRFTools_7_7_0_Installer.exe. This ran the J-Link V5.02...
I am very familiar with the arduino side but the BLE is brand new to me. I was wondering if I can use P0.00 and P0.01 to talk to the arduino and if its possible how exactly...
Debug Logger without softdevice, and the define ENABLE_DEBUG_LOG_SUPPORT to my project in the C/C++ tab.
i just test, very simple , but cannot get debug log..
int main...
I am trying to use the scheduler, but I would like to know if it is possible to have events with different priorities... As an example:
Task A - Priority LOW
Task B -...
FIXED (see below)
Hi!
I'm developing software for nRF52 on nRF52 preview DK, which I got on the Global Tech Tour.
LED blinking (blinky) example is running OK, so I moved...
Hello everyone,
I am using the great platformio toolchain that supports the mbed framework so far. I am still a newbie to it however.
I want to be able to use both the...
hi Nordic Team
The Document regarding Light Switch Example says following
The provisioner configures Button 1 on the client board to control the first server, Button 2...
Hello. I have 2 boards with nrf52832. I want to make 1 of them peripheral and the second one central. So the central board will connect to the peripheral board and send data...
I try launch example Nordic UART and get error: Error 133 (0x85) GATT ERROR
I need use stack for nRF51822 without external 32KHz crystal.
Here -> softdevice work with...
Here I am working on NRF52832 + SDK15。
I have designed two board with different 52832 package ( N52832-CIAAB0 and N52832-QFAAB0 ), I have disabled all peripheral part and...
I am using nRF51822QFAA & S120(v2.1) & SDK10.0.0
The application is to scan nearby ibeacon and send the ID information by UART. But the application always hang / reset...
When the nRF52 micro-controller is programmed through batch file i.e. nrfjprog utility, the flash fds fails to initialize.
Every time, flash fds initialization fails, I have...
Hello,
I am new to BLE as a technology and have a question regarding how Peer Manager handles bonding.
As I currently understand, the function of bonding is to enable...
I want to turn on the LED in Thingy:52 in a particular color if a particular condition is satisfied. How can I address the LED and turn the LED on in the desired color in...
Hi,
I am using the UART exmaple as a skeleton code to get RSSI from a peripheral nRF52 DK. I am working with the SDK V14 and I want to integrate my code with an arduino...
Hello, Nordic engineers. Thank you so much for spending your time solving my problem.
Currently, a custom board is made with the Nordic nRF52832 chip. As I have studied...
Refer to this post ， I did the same job to change simple_on_off model into generic OnOff Model , and I could control the LED state with nRF Mesh application as well.
I have...
Hi sir,
we used nRF 52832 ESB protocol ，
use
NRF_ESB_PROTOCOL_ESB_DPL
#define NRF_ESB_MAX_PAYLOAD_LENGTH 128
bitrate = NRF_ESB_BITRATE_2MBPS
so how can I config...
My app (S130 SDK12.3; BLE with multiprotocol support where the radio session is opened before advertising) registers function sys_evt_dispatch() as per
but sys_evt_dispatch...
Hi,
I am not yet familiar with NFC and have a question about using NFC with the nRF52.
If I understood it correctly the nRF52 is a "listening device" i.e. it cannot...
Hi Nordic,
I am trying to do a time critical data acquisition in a BLE based application.
Earlier I was using software timers. But, since the software timers are not accurate...
