pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
Hi,
I have tested AES-CCM of nRF52832 with reference to the following answered questions.
devzone.nordicsemi.com/.../
devzone.nordicsemi.com/.../
devzone.nordicsemi...
Dear all,
I did below steps to connect to the BluFruit Feather board via STLink V2:
1) Install OpenOcd and STLink USB driver as: https://pcbreflux.blogspot.com/2016...
I have some code originally working using SDK 13. It reads data from the UART and send it out in scan responses. iOS was able to capture the scan response data successfully...
hi all,
Our application is a peripheral device with sensor data that is sending up to 540kb/s (68kB/s) to the central device (data rate could probably be reduced if necessary...
Hi,
I'm trying to take the readings of temperature and humidity from 4 Nordic Thingy:52 sensors by using mesh. I did the connection of the mesh and I can control the nodes...
Hello,
I am new to BLE so I am not sure where to start. I have two nRF52832 chips, one will receive data from an FPGA through SPI and then I want to send the data to the...
For reference, in case anyone else gets a similar issue :
Using the SES import facility to import a Keil MDK v5.25 Project.
After fixing a couple of other import errors...
Hi @ll,
I'm not able to receive any ble events that should be triggered by the SoftDevice.
What I did: - Using dfu_example (added beaconing advertiser and connectable...
hi,
I use SR3 52 V1.2 for development, and I want to copy a new project to change some code.
When I changed the file name, I found it could not be compiled through, only...
Hi all,
We are currently developing a wireless system for a musical instrument and MIDI controller based on a nRF52832 (using Laird BL652 modules). Our requirements prevents...
Hi,
I would like to test the ZigBee throughput like the examples ("ATT_MTU Throughput Example" for BLE and "Thread Throughput Measurement Application").
I'm not familiar...
Dear Support,
I am working with the new SDK 15, and got some question about using whitelist without device manager, and without pairing or bonding. As stated here: https...
I'm using v14 of the SDK and I cannot for the life of me get either the external 32MHz or 32.768kHz clocks working.
How is this possible using the SDK?
Our company is manufacturing security and telecom products. In our security product range, we are adding blue tooth based product which is under development. For this product...
