Debug Logger without softdevice, and the define ENABLE_DEBUG_LOG_SUPPORT to my project in the C/C++ tab.
i just test, very simple , but cannot get debug log..
int main...
I am trying to use the scheduler, but I would like to know if it is possible to have events with different priorities... As an example:
Task A - Priority LOW
Task B -...
FIXED (see below)
Hi!
I'm developing software for nRF52 on nRF52 preview DK, which I got on the Global Tech Tour.
LED blinking (blinky) example is running OK, so I moved...
Hello everyone,
I am using the great platformio toolchain that supports the mbed framework so far. I am still a newbie to it however.
I want to be able to use both the...
Hello!
I have a device with nRF51288. And I need to fill technical specification with the following parametres: operation freq., channel bandwidth, modulation, number of...
Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Example Project: UART/Serial Port Emulation over BLE
My Environment: Segger Embedded Studio v3.52, Nordic SDK 15.2, Soft Device s132, nRF52 DK, nRF Toolkit for iOS
It...
Hello,
I have several questions regarding BLE beaconing and scanning that I feel are pretty basic but I can't seem to find the answer. I have a nRF52840 Dongle that uses...
Hello,
Thank you for considering my inquiry! I am looking for an example project with the firmware to run a gateway through the PC, nRFconnect software, and a nRF52840...
Hi,
I'm developing an application with the following hardware and software design components:
- nrf52840 DK with attached sensor
- nrf52840 USB dongle attached to debian...
Hi, I have some issues with my eclipse setup, I have installed all packages and followed the tutorial ( https://devzone.nordicsemi.com/tutorials/b/getting-started/posts/development...
Hello,
I am working on bootloader on nRF24LE1, for which a protected region should be configured. Therefore, I need to change NUPP in infoPage.
So my question is, is there...
Hi.
I watched the examples and docs with the on-off model. I tried to run these examples and configure. I don't understand when I need to use a server model when client...
I am seeing some behavior in BLE advertisement mode , that I would like to get feedback from expert in this forum. I am using modified Keyboard HID example, using nrf51 BLE...
Hi,
I'm using nrf52DK and 12.3V SDK .
in keil i can able to go to the debug session but when i press run button it is not working.
what could be issue ???
I have enabled RX address 0 only, (value of RXADDRESSES field is 0x01)
But still I got a received package interupt where RXMATCH has a value of 0x07, indicating that I...
Tx Radiated spurious emissions (1-18GHz): should be able to force the radio into a continuous transmit mode on a specific channel. The device should be transmitting with as...
Hello,
the BT specification states the following:
Is this particular requirement to be taken care by Nordic's customer using the BTIC? i.e. LE PHY qualification test...
Hi,
I want to use bsp_event_handler in SDK v11.0.0 . But the code is not getting compiled.
On building, it throws an error "error:#20: identifier "BSP_BUTTON_ACTION_RELEASE...
Hi,
I'm using NRF_LOG to print information via RTT backend (RTT viewer v6.20) and it has been working so far. After adding a single call to a function that reads 128 bytes...