hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
I made some tests with PPK-II in source meter mode by connecting a load resistor in series with a Fluke 8846A ampere meter to the PPK output. A also hooked a GW Instek GDM...
Hello,
I am a beginner when working with nRF. I am trying to run the l4_e3 solution code, but it doesn't seem to work. I can connect via BLE, but nothing is being shown...
I have problem with i2c that can't read the cst816s, its always return log message `<err> cst816s: failed reading chip id` and `<err> cst816s: Could not read x data` when...
Hi,
I am working on zigbee demo "light_switch" with NCS2.8 Add-on SDK.I enabled MCUboot according to the steps in the course " Lesson 9 – Bootloaders and DFU/FOTA "
1...
I keeping getting errors in Output terminal from nRF Connect.
I work on multiple projects in multiple different workspaces. I keep getting errors about the manifest file...
i want to advertise my one device into coded and into another device i want to do coded distance measurement it is possible to do in nrf 52840 version 2.5.1 ?
Helo, I have ISP1907 for BLE AoA.
In my understanding, the antenna spacing should be half of wavelength, in case of BLE, it would be 2.4GHz thus the spacing should be 6...
On a new board based on nRF9160 I am having trouble figuring out how to bring up the board.
I am using Azure IoT hub and can successfully build an application that can connect...
Hello,
I want to use the bq274xx.c sensor library. The bq274xx battery fuel gauge has an interrupt pin, which would allow to have the CPU idle until something interesting...
Hi there,
I'm using a slightly modified version of coap_client to test out network connectivity with a 1nce SIM card (USA). Essentially, I've modified it from a GET request...
Hi Nordic team,
I'm working with the nrf5340_audio source code from the nRF Connect SDK and have compiled the project as a gateway. When I try to connect to a headset, I...
Hello
I'm new with zephyr environment and I want to use littlefs in order to partition an external flash over spi, and to be able to upload file over BLE by using a SMP...
Hi there everyone I am new in nRF development. I was recently trying to add conexio stratus pro but i could not find it in my VS extension. What could be the issue?
Hello,
I am developing a mesh solution when the nrf52840 USB dongle will act as an observer.
I am using the mesh sensor observer sample. I am able to build and flash...
I used two development boards with 52840, Two development boards are running 'first' and 'second' in the '\examples\802_15_4\wireless_uart\secure', respectively.
Additionally...
