Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am working on light switch demo of mesh SDK 2.1.
I am using nRF52832 board, SDK 15 for softdevice and segger embedded studio for programming the nRF52832.
I programmed...
Hello everyone,
I want to develop an android app, which is able to control multiple LED Lamps in a Mesh Network.
There is an app for provisioning provided by Nordic. Is...
Hi,
When I call sd_ble_gattc_read , I receive the BLE_GATTC_EVT_READ_RSP event very shortly after -- as expected. Within the event handler (registered with the Soft Device...
Hi,
I am considering using baluns instead of discrete components next to my nRF24LE1 QFN-24 chip since board space is at premium.
In application note AN4111 regarding...
I am new to Nordic and have a simple question. I followed the instructions about setting up manufacturer specific data with BLE_Template example here: https://devzone.nordicsemi...
in the middle of the code the MOSI change from idle low to high and resulting in writing 0xFF while reading over MOSI, resulting in getting wrong data. how can i change it...
Using SDK 15.0
Example project: examples/dfu/secure_bootloader/pca0040_ble/ses
Segger Embedded studio V3.50
File main.c line 52
#include "uECC.h" <------ "No such...
chip：52832
sdk：12.3 ble_app_template
when I measure the sleep current consumption use the nordic PPK
I found there is a 30ua peak in every 20ms，could you please tell...
I have some questions to Bluetooth mesh.
1. If I have a mesh Network is it possible to have a connection to a device over all the nodes? Or does mesh just support brodcast...
Hello!
I am a beginner.
I am trying to communicate with the SD card with SPI using nrf 52832.(BLE Nano v2)
I am using fatfs of nRF5_SDK_15.0.0_a53641a. I am writing...
Hi ,
SDK：15.1.0
example：proprietary_rf \ esb_ptx
Because there is no UART function in the example, I want to add it.
The picture is everything I added, is it missing...
Hi Devzone team,
In our SDK, say SDK15.0, there is a head file called "sdk_config.h". It contains a line which looks like below:
// <o> NRF_SDH_BLE_GATTS_ATTR_TAB_SIZE...
WIth the upgrade to the new SDK, registering the callback handlers has been made more difficult to figure out.
The .sdh_ble_observers, .sdh_soc_observersers sections are...
Dear Sirs!
On one from 25 boards there is offset in ADC input about 30 ADC units. Vref = 0.6 V, Gain=6, 12 Bit ADC, oversampling 256 sample.
In other devices I do not...
