Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
I'd like to use the GATT/GAP driver from an ARM based Linux system. Is there any possibility of getting a library compiled for ARM or (cough) the source code to build it myself...
It is possible to run easily a SoftDevice stack (e.g. S110) on nRF51422 using an accurate 16MHz external clock reference for HFCLK instead of an external 16 MHz crystal oscillator...
I want to change data bytes in the advertisement packet. In ACI_DEVICE_STANDBY I put: lib_aci_open_adv_pipe(1);
In ACI_EVT_CMD_RSP: I get feedback that command 1B (I assume...
first,PCA10005 can't load sofeware hex that after s110 7.0.0 hex(include 7.0.0),and gostudio note that the given hex file can not open successfully.
second,the PCA10005...
I am following along this example on your website: Exercise 1 - Nordic Developer Academy , and currently trying to complete this excercise: Exercise 1 - Nordic Developer Academy...
Hello,
I’m working with a custom board using the nRF54L15 and the latest Nordic SDK, and I’m facing an issue while trying to communicate with an nPM1300 over I2C.
Here...
Hi, I tried to migrate my project from nRF Connect SDK v2.5.3 to v2.9.0, switching to sysbuild and creating my own board definition instead of using a overlay file.
I decided...
Hi Community,
I designed a similar board asThingy53, espacially the antenna parts are almost the same, except the RF switch, we replace it with another one (BGS12WN6E6327XTSA1...
Hello,
I use SDK v2.9.0 with nRF52840 and my application is based on peripheral_uart example.
Have I understood correctly that nRF52840dongle has preloaded (by Nordic...
I have a custom board (nrf5340) and can debug it, but it will not print to J-Link RTT Viewer. The main looks like this and I tested with a breakpoint on the LOG_DBG using...
Hello! I'm looking for a way to include fast charging capabilities in my product, while still allowing USB2 data to pass between any host PC and the nRF52840. As I understand...
Does Zephyr support automatic reconnection of the Wi-Fi if a connection is lost? I can't find any documentation on this, or code examples. It seems like every example connects...
Hi, I have custom board with nrf54l15. Im using sdk 2.9.1 and nRF54L15-DK as debugger/flasher. Im able to flash firmware correctly using SWD, or do nrfjprog --recover, but...
According the nPM2100 page "nPM2100 comes with exceptional software support for Nordic’s nRF52, nRF53, and nRF54 Series" but doesn't mention "nRF91 Series".
Currently I...
Hello, I searched the forum for similar issues and found a few, such as
I am currently implementing a PSRAM is66wvs4m8 on the Thingy 91 via SPI, using SPIM3.
The problem...
I need both zephyr power device management and the low power features of LPUART in my project.
However, enabling PM_DEVICE raises idle current consumption by quite a bit...
hello to all.
i been strugling the last couple of days to make a simple PPP connection from a debian12 laptop to the internet passing trough the nrf9151. I followed the...
Hi,
I want to produce a pulse with 4 seconds length from p0.25, but i am failed.
#include <zephyr/sys/printk.h>
#include <nrfx_pwm.h>
#include <hal/nrf_gpio.h...
Hi
Is it possible to stream 128 kbps .acc, .lc3 or .mp3 Spotify audio from server to nrf9151 ?
It says it supports 300 kbps download, so maybe 150 kbps is realistic ?...
