Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
Hello!
I am trying to change the connection interval of the nRF8001 (connected to the PCA10000 usb dongle). Changing from 7.5ms to 1sec is very fast, but changing it back...
int SEGGER_RTT_printf(unsigned BufferIndex, const char * sFormat, ...)
why only BufferIndex=0 can display information on RTT viewer?
How to output different colors to...
Hello I have this code that sends some L2CAP packet to bluetooth device. I want to do the same for BLE device. Could someone please tell what I have to change on that code...
Hi
I use NRF51822_XXAC + s130_nrf51_2.0.0_softdevice + nRF5_SDK_12.3.0_d7731ad, IDE is segger embedded studio 3.40, my program works well when i set optimize level to...
Hi all,
I'm Carles from Nordic and I'm happy to announce that O'Reilly has recently published a new book "Getting Started with Bluetooth Low Energy" of which I am a co...
Dear Nordic Team, Thanks for supporting.
I want to know how to set user MAC address in SDK12.3.0 for nRF52832. I am using ble_app_blinky example. Please support anyone....
Perhaps the following defines added to the beginning would make user specifications a little clearer
#define Default 0
#define Black 1
#define Red 2
#define Green...
Hello,
I'm trying to run my application from Segger Embedded Studio into my custom nRF52840 board but it is not working !
I switched to Jlink commander to get more details...
Hello,
I am migrating a BLE project from SDK 13.1 to SDK 15, and am running into an issue with SPI functionality. I have followed the migration guide for 14.2 to 15, changed...
Part 1: A device that is exposing Mesh Provisioning Service[as a unprovisioned device] or the Mesh Proxy Service [as a provisioned device] could under-utilize the negotiated...
I am using nrf52832 and i want time.
I am using nrf_calendar_example https://github.com/NordicPlayground/nrf5-calendar-example .
My problem is it gives only resolution...
Hello all,
I have noticed that a delay appear periodically when writing SD card for example, I have something that the following code
Unfortunately, I have a jump...
Hello Nordic Team
I am working on nRF52832 MCU, SDK-11. I want to calculate available space so that I can save custom sensors data in chip.
According to datasheet we have...
I am working with nRFx modules and have a few questions about updating parameters. I started my project with an example and modified what I needed. However, I am not sure...
Hello Nordic experts,
I am trying to add an output endpoint to the usbd_hid_generic example in nRF5_SDK_15.0.0_a53641a. I exactly followed the suggestions in
https://devzone...
