Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Hi there~
I want to install and run my own nrfutil on my pc run with windows 10, but I cannot get throw it.
After generate the exe file, nrfutil outputs some error.
...
Hi,
I am trying to build an "asset tracking" application in Windows 10 using power shell, but it failed.
Please find the logs below and direct me to the correct path....
HI,
I am trying to load the Asset tracking project in segger embedded studio, but it is giving the following error:
Segger Embedded Studio Version: " SEGGER Embedded...
I'm looking at reference schematic/layouts for the NRF52840 and fail to see how the PCB antennas are 50 ohms. (I understand that it's frequency dependent, and that resonant...
Hi,
I'm doing power measurements for nRF52-DK (SOC nRf52832) and for nRF52840-DK. I'm able to measure reasonable figures from the external supply connector (P21) of nRF52840...
Hello,
I was trying to open assert tracker application on MAC os, in segger studio v4.18.
However, after I open the "Open nrf connect SDK project.." and filled out the...
Hi,
We're seeing DFU issues on iOS that we're not seeing on Android. To make things simpler I've reproduced the problem with pca10040 and nrfconnect for iOS.
I'm using...
Dear support,
I am experiencing an issue while using the SPIS peripheral. The issue seems to be the same one as https://devzone.nordicsemi.com/f/nordic-q-a/33727/new-in...
Hi,
We use the ECB peripheral to encrypt and decrypt data with a proprietary driver implementation (which is not that different from the one in the SDK). It is working fine...
Hi,
We are looking for information about the possibility to integrate the NRF9160 in our new product which is integrated in a sealed metal enclosure.
I have not made any...
Hi,
currently i'm dealing with problems with this https://github.com/NordicPlayground/fw-nrfconnect-nrf/pull/1300 pull request which have wrong title and wrong changes ...
Hi everyone!
I'm wondering, is FSK compatible with the nRF52832. I want to emit 2 differents frequencies that the receiver will be able to recognize. If yes, How to create...
Location: Utah.
Well, I was testing a Thingy:91 board here with the very first boot and test with the iBasis SIM card which comes with the product.
Everything goes...
Hi,
I have qestion about crystal 32.768 kHz follow schematic as attached file.
Is it nessary to use ?
Is it possible, Can I remove this crystal ?
Thank you
Best...
