I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Is there a function like battery_level_in_percent for AA battery?
I know battery_level_in_percent is only for CR2032.
Even though I compensate it to make it 3V from AA battery...
Hello,
I want to use the nRF52832 as native transceiver 2.4GHz and I'm looking at examples of the latest SDK.
I'm using Segger Embedded Studio.
I found some examples...
Hi, I'm on final development stage of my custom board. I'm using nRF52840 with nRF5 SDK v15.0.0 and S140 SoftDevice v6.0.0. I need to trace the over-the-air communication...
I'm not using a softdevice, and am doing some time critical measurements when the radio begins transmitting.
This code works very well with nrf51:
__disable_irq(); NRF_RADIO...
Hello
I have a question i cannot figure out. I'm using my phone to send string on my NUS client (NRF52 with SDK15.3.0 and FreeRTOS) and the event BLE_NUS_EVT_RX_DATA is...
Hi,
I am new to development with Nordic chips. I am using nRF52840-DK (SES,nRF5_SDK_15.3.0_59ac345) to read analog input on ADC pin AIN0. I want to continuously read the...
Hi,
I used a NRF52832 to test our product with Python Script.
I enable my notification. I start to receive notification and I have a crash after received first notification...
I've used the DFU bootloader from SDK 14, s132 and the ble app uart example as a boilerplate for my app.
Now i'm looking into making some relatively large changes to the...
Hi,
I have problem compiling "HTTP application update" sample form the SDK for the NRF9160. I am using all the latest tools: * segger embedded studio: v4.18 * nrf SDK v1...
Hello,
I had problems connecting the periphery to the central. When I connect them, I get notifications like this from peripheral, but after this message they don't lose...
Hi,
We are using nrf52 dev boards running mynewt and until two days ago we could use the app to identify/provision and get composition data for nodes and get composition...
We are in the final throws of testing our boards that are based on the BLE UART Peripheral application. The current test environment involves monitoring board and battery...
i changed the code to send environment data over ble_nus service and it was worked
so i tried to send motion sensor data over ble_nus service and i changed code but no data...
Im developing a mesh network based on a custom board using the nRF52832.
I fine with sending some bytes over mesh . But now i want so send more bytes over mesh using Instaburst...
Hello,
I am using nRF52840, SDK_16.0.0, S140 SoftDevice and Segger 4.16 for flashing the image. I am using ‘ble_app_blinky’.
I have few queries on setting Tx power...
