Hi all,
I've built a custom nRF9151 board, which is successfully responding to the basic factory AT commands. It won't accept a CFUN=1 command though, presumably because...
Hello!
I think there is a problem in NCS v3.3.0. nRF54L target, sysbuild build with MCUboot and TF-M, partition layout coming from devicetree (SB_CONFIG_PARTITION_MANAGER...
Hi, I'm developing a keyboard-pcb with NRF52840. I'm doing this as a hobby and are not that experienced with integrated circuits. Anyway, I designed and produced a pcb, but...
Hello,
in cases where the LTE signal strength is extremely low, we observed that the LwM2M /4/0/2 RSRP rolls over from -128 to 127. We found that the nRF Connect SDK uses...
As part of the Bluetooth LE course we need to setup and install the nRF BLE sniffer for wireshark. I have followed the explained steps in the course to set up wireshark to...
The at command documentation says that ENVEVAL is only available in system mode 2 (CFUN=2). Is there a reason why the command can't be run in any other mode? For example if...
Hi
The TWI driver has a twi_clear_bus() function but the TWIM does not.
I'm getting an I2C error, and need to do I2C soft reset. I'm doing this manually at moment but...
Hi,
I am currently in the process of interfacing the HMC5883L magnetometer with my nrf52 development board. I have verified the connection to be working using a logic analyzer...
I have one central(SDK 10.0 S130) and one peripheral(SDK 8.0 S110) device. Normally central device can connect peripheral device it's ok but the peripheral device will stay...
Hi Nordic,
I'm porting hrs application on nuttx OS. But when I call sd_softdevice_enable function, it goes to "RESET". I read below article which mentions that SVC handler...
Hello all.
I'm having some problems with compiling the bootloader_secure project:
I downloaded SDK zip from http://www.nordicsemi.com/eng/Products/Nordic-Thingy-52 and...
Hi, I would like to detect the presence of a particular device in an environment where there are many devices advertising. The advertising packets are received by a scanner...
I want to send the continuous data over the BLE which is received by the UART of my nRF52 Evaluation kit. The BLE connection is getting disconnected while sending bulk of...
Hello Everyone,
I am new to BLE world.
Currently using MDBT40 which has nrf51822 as core: www.raytac.com/.../MDBT40-ANT-D.pdf
I am following this repo: github.com/...
I want to use nRF51822 Bluefruit LE Friend device (blue board) as BLE Sniffer. My OS is Windows 7 64-bits.
I installed ble-sniffer_win_1.0.1, v1.0: FTDI Driver Requirements...
According to another question here:
devzone.nordicsemi.com/.../
I'm stuck with waiting for the LFCLK to boot forever.
Normally, keil has a .s startup file that dictates...
Hi,I use the SDK 12.2.0, I want to add the peripheral RTC example to the ble_app_uart.I find the softdevice have used the RTC1 ,so I want to use the RTC0,but when I added...
Hello,
I am seeing something strange wrt to reassigning the NFC pins (9,10) on my Rigado BMD-300-EVAL using nRF SDK12.1 and gcc to build. I have two SPI based sensors on...
test_ble_mouse_wo_bootloader.pcapng Nordic_Mouse.pcapng connect_to_phone.pcapng test_ble_mouse_1.pcapng test_ble_mouse.pcapng Hoping someone here can help. The setup is a...
My problem seems to be related to this unsolved question.
I've making a central application to connect to my peripheral but I'm having a hard time getting the service discovery...
Hi friends..!
I am trying to print data on UART but only just after when TIMEOUT (180 sec) occurs in the project BLE.zip .
Is there something BLE stack event has to be used...
I have BP device, It has start button. When we click the start button then it start monitoring the BP. Need to start/stop the device to monitoring the BP from the iOS App...
