Hello!
I think there is a problem in NCS v3.3.0. nRF54L target, sysbuild build with MCUboot and TF-M, partition layout coming from devicetree (SB_CONFIG_PARTITION_MANAGER...
Hi, I'm developing a keyboard-pcb with NRF52840. I'm doing this as a hobby and are not that experienced with integrated circuits. Anyway, I designed and produced a pcb, but...
Hello,
in cases where the LTE signal strength is extremely low, we observed that the LwM2M /4/0/2 RSRP rolls over from -128 to 127. We found that the nRF Connect SDK uses...
As part of the Bluetooth LE course we need to setup and install the nRF BLE sniffer for wireshark. I have followed the explained steps in the course to set up wireshark to...
The at command documentation says that ENVEVAL is only available in system mode 2 (CFUN=2). Is there a reason why the command can't be run in any other mode? For example if...
Hi
The TWI driver has a twi_clear_bus() function but the TWIM does not.
I'm getting an I2C error, and need to do I2C soft reset. I'm doing this manually at moment but...
I recently completed a field-upgrade path from an nRF5 SDK 17.1 application (with the legacy Secure DFU bootloader) to a fresh NCS-based firmware stack, while preserving user...
Hi all
I'm working on a custom board using gcc and eclipse.
My primary problem is I'm fighting with the ld settings for the secure bootloader.
I activated the RTT which...
Hi,
I want to write calibration and configuration datas in to flash and read it back. By using sd_ble _flash_write API function , I can write up to 520 words(520* 4 bytes...
Hi, all!
nRF51822 had been used in my project, because of dual bank bootloader and softdevice, the
internal flash memory was not enough for the application. I want to...
Hi there,
I need to add more the function based on Bluetooth, and I need the better security of the function. However, I do not want others read flash data freely and I hope...
Hi
I'm preparing for some tests and I'm wondering where I can find information about what the expected percentage error rate should be?
Right now with 2 nrf boards connected...
Hello to all nordic jedi masters!
I have made an observation, on which I would like your confirmation.
My combo is: nrf52832 + SDK 11 + SD132.
Will my application ...
I'm currently writing my thesis, and my goal is to establish a network protocol like IP. We need to transmit about 200kB of data between 2 or more nodes once every 10-30 minutes...
I am programming a device with a NF52 that uses a hall effect switch o enter/exit sleep mode when BLE is in advertising mode. When connected, It will generate a separate BLE...
Hello,
i have a strange behaviour on a board with nRF52. The board is flashed with SD 4.0.2 and bootloader.
On Keil If i load the bootloader with JLink, it runs and...
I'm using nrfutil version 2.0.0 and have noticed a strange bug today when generating a new signed application image for bootloading.
If I have a version number of 0207...
hello , I am new to SPI protocol.I am using NRF52 DK &nRF5_SDK_13.0.0_04a0bfd( pca10040) using keil-5. I want spi master example code. Can any one suggested me where I find...
Hi there,
The S132 SoftDevice for the nRF52832 has grown in size from 0x1F000 for release 1.0.0-2.alpha, to 0x23000 for 5.0.0-3.alpha. It appears that the nRF52840 will...
I have a small PCB I'm prototyping/assembling, based on a nRF52832 with a few sensors. Looking for someone here to help me with writing basic firmware for testing the board...
