Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Apologies if this has been asked before but did search for 'format' in faq and got nothing.
I have been answering to questions.
In my answer I place hard empty lines....
Hi
i use nrf51822 s110 "hrs" example to transmit the data to ios.
I need to add an option to send back some data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hi,
I just finished compiling my code for the nrf51 to take ADC measurements and send the hex values over ble tuart o my iphone. Now I want to see if I can send that data...
Hi, i know maybe this question was asked before, but i have a particulary issue.
I have 2 devices connected through BLE. Just when them get connected i need to send a byte...
Hello!
I need to read a string from UART, there's code below:
unsigned char GetChar(void)
{
while(!RI)
;
RI = 0;
return SBUF;
}
int Readfstr(void)
{
char...
Hardware: Rigado BMD-200 B using the nRF51822_xxAB
Bootloader: dfu_dual_bank_ble_s110_pca10028 with the device set to nRF51822_xxAB
Softdevice: S110_nRF51_8.0.0
DFU Tool...
I'm trying to use BLE library for python to communicate with one Nordic nrf51844 chipset. Because one characteristic is notification enabled, I need to enable notification...
Does there exist a white paper describing some typical PPI use cases with coding examples? The only one I've found is the peripheral/gpiote example and it is severely lacking...
Updates are moved to the end of the question
I created a modified version of pca10028.h and boards.h and have preprocessors changed so that the following new config is...
I example test ble_central and ble_peripheral of ble_app_uart.
Radio TX and RX test is OK.
It confirmed the data communications relating to uart_event_handler function....
I'm trying to get a time stamp using app_timer_cnt_get(&ticks), but the ticks always equals 0. And I have called APP_TIMER_INIT() to init the app timer. I have no idea why...
Hi everyone, I have been given a nRF51-DK board and I should use it to send data retreived from a sensor to it through Arduino, to finally receive it in my cell phone. I am...
Hello everyone,
I'm brand-new here. I have developed quite a bit of software on desktop PC's, but this is my first experience with embedded programming. A few weeks ago...
Hi Team,
So I downloaded the new nRF Connect for OSX. I inserted my PCA10031 nRF51 dongle into my USB port and the relevant lights lit up. However nRF Connect does not...
I am quite new to embedded firmware development and definitely just two days old into Nordic nRF52 development.
I want to just setup a 25% duty cycle clock output on GPIO...
Hi,
I have a very sophisticated program on nRF51822 with SD120 which uses SPIS (as an RX for another board) and UART. I used "spi_slave_example" as a base program.
I am...
