Hello Nordic Team,
We are trying to test an I2S DAC (MAX98357A) with the nRF54LM20B EVK . Could you confirm if this is supported and which sample application is recommended...
I am trying to enter MCUboot serial recovery mode on an nRF5340 through a UART command.
I mainly followed the Nordic tutorial below:
https://academy.nordicsemi.com/courses...
We are using a custom board based on nRF54L15 with MCUboot and compressed image DFU over OTA. DFU was working correctly when updating between NCS v3.2.0 and v3.2.4, but after...
Hi，
I use NCS 3.2.4 and 54L15 DK. In the DFU target, I added configuration
and also added the following content in dfu_recover function.
After the distributor...
Hello, I am developing a low-power nRF52840 product using the ncs Zephyr environment. Currently, I have suspended peripherals such as UART and I2C, allowing the system to...
Hi everyone,
I am currently facing an issue with the nRF54LM20A where the access port protection is not taking effect after programming SECUREAPPROTECT and APPROTECT into...
I'm curious about the approach taken in the nRF Connect SDK's location library for cell neighbor scans ( https://github.com/nrfconnect/sdk-nrf/blob/main/lib/location/scan_cellular...
Hi,
I'm currently using an application that needs a very speed detection of GPIO and need to use NMI on GPIOTE.
I tryed to find how can I connect my NMI to GPIOTE but...
nrf_drv_usbd_init() calls nrf_drv_clock_hfclk_request(NULL)
however nrf_drv_usbd_uninit() calls nrf_drv_clock_lfclk_release();
Is this correct?? If so why?
Hi, I have the opportunity to bid for some research funding for my project, and I'm thinking of speccing a workstation for processing video in realtime, and sensor data in...
I am trying to add the heart_rate_meas function to the ble_app_uart project.
Is this plan possible?
However, it does not go well.
Why are you concerned with this method...
Hey Guys,
im working on some sort of application transport layer for ble and have some questions to better plan what i need and what is kind of redundant.
Is it correct...
Hello everyone,
I am using nrf52832 with SDK version 11.0 for an IoT application. I am communicating with Atmel ATWINC 1500 module through SPI in order to connect to Wifi...
I'm using nrf52 with SDK version 12.0.0. I'm trying to use the FDS for my application. I used one of the existing fds example from link fds_example .
With this example...
Hello,
I am a bit lost, after concluding the application part of my project I try to approach the ble part.
I read the "Getting started with bluetooth low energy " and...
Press down PWRON1 give rise to Q2 and Q3 conduction, the 51822mcu power on and IO send a hight level to PWRON,to keep VCC_nRF.
At this time press a lot of button will not...
Is there an unsecure version of the bootloader? I'm looking for something that will take anything as an upgrade.
I figure if I'm stuck in the bootloader anything is better...
I want to set up a rPi3 as edge router for 6LowPAN over BLE. Ideally I would like to have random devices (users) come and go by dynamically connecting to the router. Same...
i am using eclipse IDE. while flashing my code to nrf development kit it is showing like this and also in the console it is showing that flashing is done.
console:-
SEGGER...
Hi
For new BLE project we planing to use slave that allow few (3-4) connection at the same time. i.e After the master (phone) connected to our slave, the slave continue...
