Hi, the nordic team
I am working on thread protocol using SDK version 2.9.1.
I use the SED device,My poll is 1000 ms. How can I receive messages from my parent node when...
Hello,
I am using the nRF5340 in my project, and the device is capable of communicating with a mobile phone over BLE . However, we occasionally encounter a connection error...
I work for ChannelSounding on nRF54L15.(NCS3.0.1)
I measured the distance using two nRF54L15-DKs. The actual distance was 3m. The average measurement result is shown below...
The nRF52832 devices have been produced in hundreds of units. Currently, it has been found that individual central devices are problematic – connecting to peripherals often...
Dear everyone,
I'm currently working with the nRF7002DK and attempted to build and flash the following project from GitHub: MQTT over WiFi nrf7002DK
However, when building...
Hi,
Is it not possible to import a key which can be used for multiple use cases?
I would like to import a single key which can be used for HMAC & HKDF.
Is the below...
System Info: Hardware: M3 Max OS: Sequoia 15.3 Following the instructions outlined in the readme of: github.com/.../nrf-docker Docker fails to build an image on Apple Silicon...
I am looking for a device with support for the 4.2, long packets (up to 255 bytes) feature. I see that the nRF52 is a 4.2 device. But for what I understand the optional long...
I am using s120 for central device, and my central device connects to multiple BLE slaves. After connection, some slaves may lost connection due to power off of that device...
I want send ble bond connection request from raspberry pi to nrf51882.
Can you please let me know which ble libraries I need to send central ble bond request to nrf51882...
Hi,
My goal is to capture on gpio burst infrared proprietary "messages" composed of multiple "bits".
The Length of each bit is around 100 to 200us.
Initially I planned...
(I understand my question is similar to devzone.nordicsemi.com/.../ , but I would like some additional clarification not provided in that post.)
Hello, I've been developing...
On a BLE_GAP_EVT_CONNECTED, I'll send some data to an attached microcontroller via UART. The code will expect a response of that data, all while being inside that BLE_GAP_EVT_CONNECTED...
My application involves the Nrf52 using softdevice and a slave only SPI ADC running at approximately 26khz. The ADC has a pin interrupt to indicate data ready. There seems...
Building nrf_delay.c (or anything else including nrf_delay.h ) with NRF52 defined produces:
arm-none-eabi-gcc -I C:\Nordic\nRF5_SDK_11.0.0-2.alpha\components\device -D_DEBUG...
Hi, someone know whi when i press disconnect on iphone the nrf51 restart from the mail?!
Why if i disconnect android device the chip does not restart as the iphone?! is normal...
I'm trying to build BLE driver 0.5.0 for 64bits.
I've downloaded:
MinGW 4.8.2 64bits
boost 1.56 and compiled it using address-model=64
CMake 3.4.1
Python...
Hello Nordic community:
I've read about Serialization in the nRF51 SDK doc and would like to prototype an example with it.
I saw a notice of it being removed post 7...
Hi,
Is it possible to get a more detailed description of the GPIO block than what is available in the reference manual? Specifically i'm interested in how the disconnect...
Hello Everyone,
I want to run a couple of test on the nRF51422 radio. However, how do I go about checking the firmware on these devices without the use of a motherboard...
Our device fetches fused quaternion from MPU and transmits via NRF 51822.we are using 3.7v li-ion battery.we are using Non-volatile memory.
Currently we are facing these...
