I am developing an application for an NRF52840 using Zephyr and trying to run unit tests on startup. My application sources are in my src folder, and my unit ztests are in...
I'm trying to set a public custom BLE mac address to my device but the flag CONFIG_BT_HCI_SET_PUBLIC_ADDR is not enabled. If i try to set it to true on prj.conf file the code...
I know this pin is used in QSPI even after disabling the QSPI I am unable to toggle the GPIO what is the reason.
And this the sane pin I'm using for I2C that's not working...
Hello,
I am working on a project using the nRF Connect SDK, and I need to implement both BLE HID and USB HID. I would like to know:
Is it possible to use BLE HID and...
I have a requirement where I'm using a .NET-based test adapter that communicates using the Modbus protocol over a serial (COM) port.
Now, I want to develop a BLE Central...
Hi,
My product uses the nrf52840 chip with NCS 2.7 and has a USB mass storage function.
I would like to implement a feature as below
1. When the USB is connected to...
I'm a new software developer and I'm not a native English speaker. If I ask questions through a translator now, the description might not be clear.
I'm currently facing...
I have successfully gotten the DFU to work on the NRF51422 S310V2.2 softdevice. I can download blinky app via the nRF Toolbox DFU application and all works great, but when...
Hi.
I am new to this forum, and can be described as a programmer with very little embedded experience.
I have bought a nRF51822 BT SMART BEACON KIT, and are trying to...
Hello,
i would like to turn off a sensor completely when unused and thought of powering it through the GPIO of the Controller.
I wondered if it is recommended or do the...
We have updated multiple android phones to nRF Toolbox for BLE app and we are all getting "Unfortunately, nRF Toolbox has stopped." error message when opening the app. nRF...
Hi,
I want to get a notification when the BLE event is started, in order to start a timer just after.
How can I get that?
I want to clarify my question :
My board...
I use the NRF 24AP2E in my communications, and I need detect if the communication is good.
I active the RSSI message, but in scanning mode I don't receive byte 0x20 in Measurement...
Hi All,
I am designing a circuit with nrf51822 and mcp25625 (microchip spi can interface). mcp25625 has an internal 16mHz xtal clock circuit and a digital clock out, I...
Hi, i'm kinda a newbie on this, and i'm trying to port the SDK available for arduino to a PIC, i followed the instructions on the SDK and also here
Now i want to verify...
I ran into an issue recently of attempting to make a pstorage_update call from the callback set in pstorage_register . It resulted in a difficult to track down error, so I...
I have a USB dongle of nRF24LU1p and it is identified as the Basic Remote firmware with a VID:PID of 1519:002B. I would like to reprogram it over USB but do not know how to...
For nRF 51822 radio transmission, the payload packet is started at the NRF_RADIO->PACKETPTR. Then what is the packet size? is there any parameters to control the packet size...
I should have an own function wich is called upon after Port 3 goes low. I haven't succeeded yet using ppi channels. (I'm using the NRF51422)
For the moment the code is...
Hello folks ;
I'm new here and glad to have such kind people around to see helping those other developers ..
Here is my question
I'm using one of the NRF24L01 modules...
Hi,
I'm using the attached circuit and we recently took our product to FCC testing and failed the 2nd harmonic because we were transmitting too much power.
I'd like...
