I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
Hello,
I have migrated to the latest version of the sdk11. However, I get a nrf error 4 when I call sd_ble_uuid_vs_add. Multiple people on this site have been having this...
I am trying to port blinky_blank (no SoftDevice) to my target and started by creating a custom_board.h header file with correct GPIO pins for the LEDs and duplicating blinky_blank_pca10040...
Can anyone help me reading IO capability in Android? Basically there is a known bug in some Android versions across different manufactures where Android reports wrongly IO...
I want to use chacha20 cypher to encrypt and decrypt a 64 byte message and send it over BLE. I tried using wolfSSL, cifra both of which provides the implementations but there...
Hi,
To measure the transmitted RF power (to reach EN 300 328) we Need some ATT commands to set fix channel and maximal output power. In additional we test the EN 55022...
In this previous discussion on minimizing power consumption on the NRF51-Dongle, it says:
You are using evaluation kit or
development kit and LEDs are connected
on...
My system is a BLE peripheral with 2 states. There is a characteristic that represents the state, and it can take 2 values: 0 and 1.
You can read the state, write it (force...
When the supply voltage drops below 0.6V and then get back to 3.3V the nrf51822 starts up in an undefined state and often some flash pages are corrupt after that. Is this...
Hello,
We're currently running softdevice s310 v2.0.1 with SDK 7.1.0 on the nRF51422-QFAAE0 (ie. rev 2). We're planning on upgrading to the nRF51422-QFAAF0 (ie. rev 3)...
Hi!
I was using SDK11 alpha previously and when the official version (89a8) got rolled out I started integration. First thing was the missing S210 and S130 softdevices...
Hi together,
I'm using the NUS example (NRF52832) for client and peripheral, which is running quite well. My goal is to inform the peripheral application when notification...
Hi,
I am using nrf51822 chip and i have compiled the TCP Client example from IOT SDK in eclipse.I am using Master control panel as a central device to discover the device...
I want to measure a current consumption for the 3rd-party evaluation board which has 32MHz crystal and 32KHz crystal, and there is not PO.18 on the 3rd-party evaluation board...
Hi,
I use nRF51822.
Is it possible to change a beacon timing of the advertiser by a trigger of the acceleration sensor in the advertising mode?
Thank you for any...
Hello everyone,
I compiled the nrf51-app-button-examples without any error and warnings but it is showing me this error (No cortex -M Device found in JTAG chain / Target...
