Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
Hello,
I have a device based on nRF51822 revision 2 and SoftDevice S110 v7.1.0. Because it is revision 2 it is affected by PAN44 and PAN45, and by default the SoftDevice...
Hi Guys,
I know this is more for software issues. But I was curious as to where I can find trusted case providers/makers for the nrf51822 Beacon. Can anyone from the community...
Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
I have an external 32MHZ crystal on my custom board.I want to configure it to 32 MHZ external crystal to operate the chip. i changed the some register configuration in software...
all works fine with iphone that mean data stored, bond 's information that has been persisted during DFU processing.everything works with iphone. but when the device that...
Dear Nordic Team,
Thanks for supporting.
Now i want support for single channel(Ch 37) advertise , please support anyone. I am using ble_app_uart example.
My SDK : SDK12...
I'm running some stress tests on a nRF52832-based product, with the following setup:
- SDK 12.0.0
- SD 3.1.0
- Compatibility modes 1 and 2 enabled.
The device exposes...
hi ,
1. How do I migrate the codec OPUS part of SR3 ? I want to use it for audio. But migration always fails. Any migration examples?
2. How effective is ANR work? Are...
I use blinky_freertos demo on nrf52832,
now I want to disable FPU,
but when I disable FPU in Keil MDK option->Target Floating Point Hardware Not Used,
there is an error...
Hi,
i am using nrf52, sdk11 and S132v2.0.0. so i want to flash the hex file using OTA so that, i have create zip file using fallowing command.
**nrfutil dfu genpkg --application...
I've been trying to set up my nRF52 DK on my mac OS.
I followed all the steps to download the SDK (15.0.0), the Command Line Tools, the ARM GCC toolchain, and the J-Link...
Hi,
I have a few doubts regarding Subnet in Bluetooth mesh:
1) If a node including in 3 subnets, how it manages to switch between multiple subnets?
2) What are the various...
Hello,
I am using nRF52832, s132_nrf5.0.0_softdevice.
I am trying to build a ble gsm gateway.
I have 3 different peripheral devices. They have some services.
On my...
Hi
I am using SDK 14.2 secure bootloader with IAR and SES build. My IAR project is working with DFU upgradation but my SES Hex file is not working
Procedure Followed...
Hi, I use s132 and SDK15 to work with nrf52832. In code I set up RTC and CC to trigger every N ticks. It works as expected and time periods counted correctly. However, when...
Hi,
I can't find the whisper mode（-30dbm TX power） on nRF52832, which is available on nRF51822.
Does is have been disabled on on nRF52832?
Regards,
Aaron
I like to build a node act as client as well as server. Is it possible to build as control model in mesh and shall i get any example for control model. Please give me any...
