Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Hi!
I get the RAM adjustment warnings when running my nRF52 system:
RAM START ADDR 0x20004000 should be adjusted to 0x20001FE8
RAM SIZE should be adjusted to 0xE018
...
In my application I send a characteristic notification from inside a timer callback function. This causes a restart of my application if I am connected to the board. But my...
It has developed a eddystone-url in nrf52 device based on the current nrf5-sdk-for-eddystone project.
But I would like to know the Nordic's policy about this.
In other...
Hello Everyone,
I wrote the simple software for long push 3 sec and long long push for 5 sec and it is working fine as expected but can anyone suggest me how to create...
Hi there.
I'd like to start measuring the current consumed by a custom board with an nRF51822 on it in various states using a scope. I've read the DK user guide advice...
Hi,
We've developed a prototype for a client and just received the nRF51 chips for production. Problem is that the chips that just arrived is an older revision than the...
Hello, I Preparing the KC (korea-certification. about bluetooth)
KC requirements as follows:
Set Test Modes
Set Continuous modulation mode
Set Unmodulated Continuous...
Hi all,
I'm having a tight deadline upcoming and have run into an anoying problem.
I'm using this NRF51 breakout board: ohtcom.com/.../nrf51-m0-module
I ordered a...
HI I am trying to make 5 characteristics on Nordic and my program does not compile for NRF51822 QF AA or AB. but compiles fine for QF AC. what could be the matter. I get an...
Hi,
At command, I'm sampling ADC for a short period of time. What I noticed is that the current consumption of the chip goes up 2mA, even after the sampling is stopped...
Hi,
What is the actual difference in hardware between the two chips? I know they support different soft devices but is there any actual difference in the hardware? Or is...
Does having monitor mode debugging or using RTT print statements increase the quiescent current of the nRF52 even when the debugger isn't connected? I am using S132 SoftDevice...
I'm in the process of porting code from a PCA10000 rev2 board to a custom board, using the ISP130301 integrated MCU (contains a rev3 nrf51822 IC). I'm using nrf51 SDK 6.1...
Hi,
I use an nRF51822 QFAC A1 and my goal is to disable BLE in a powerdown mode, then when I press the pushbutton I want to restart BLE.
Tried using BLEDevice::shutdown...
