[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
if the issue can be worked ,how to do that with android source code? the 2 ble pure devices (not android phone) connect with a ble android phone.
please check below, the...
Softdevice Version： 8.0.0
SDK： 9.0.0 IC：
NRF51822 Rev 3
service： NUS ANCS
When the application is not downloaded, the bootloader is working.
After serial bootloader...
Hi please help,
We are facing a problem of Gazell failure (not getting interrupt on gazell ISR) when i perform external Flash write using SPI.
If i disable gazell and...
hello there i downloaded nrf5 iot sdk. i have nrf51 and nrf52 kit.now it has many example codes like tcp,udp. can anyone tell me how to test it with my kits??
Hi everybody
Can nrf51822 advertise with a Balun whose SE pin is disconnected? (not connected to antenna, just left disconnected)
Just like the reference circuitry above...
Hello,
I can see, that sd_ble_gatts_hvx() returns 13313, if the notification is not enabled for that characteristic from the connected central. --> S120 Softdevice runs...
Hi
I got my new NRF51 DK. I was able to test it with blinky using mbed. I had to add the add the device nRF51-DK. then compile it and drag the .hex file into the mbed drive...
When I first got the nRF51-DK board... I was able to see this board on nRFgo. I then added the s130 hex file to it.. Since then when I connect this board, it does not show...
Hi,
Everyone,
I am trying to achieve minimum current level, I can possibly achieve, with continuous BLE transmission
so, I tried running BLE_POWER_PROFILING_APP given...
Hello to everybody.
I've buy a nrf51822 module with a motherboard.
i struggling to programming an uart over bluetooth example but i think something missing.
With nrfgo...
We configured nrf24LE1 as PRX and nrf52 as PTX and the packet sent out every seconds.
The nrf24LE1 will only received the packets every twice packet sent out and both packet...
I tried to use difference Data Rate for testing the transmit distance. Don't know why using the 250k bit is worse than using the 2M bit & 1M bit. The distance will decrease...
I am debugging a small program for the nRF52, which uses the App Timer and communicates over UART. I am trying to keep up with bug fixes, and so I'm using SDK 11.0.
The...
We have an application that requires a fairly quick disconnect (under 250msec) when the RSSI exceeds a threshold, for example -80db. Unfortunately, around 1 out of every 4...
I am trying to program a nrf51822 module using the nrf51-dk.I have made connections as per the nrf51-dk user guide, but sme is not working...
I am using the Vdd of the...
Hello all,
In a network of sensors with power constraints in a room which protocol is the best?
Newer devices seem to use BLE but I don't want to discard good old nrf24l01...
