i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
Hallo,
I try to port some existing BLE application from SDK 12.2 to SDK 14 that used the S132 Softdevice.
With 12.2 it was possible to configure bandwidth requirments...
Would it be possible to use BLE for a sensor network with aprox. 40 battery peripherals measuring a float at 100hz? 50hz? For one central unit, or how many if needed.. The...
Hi,
One of my pca10040 stays on bootloader mode.
I have tryed copying J-Link OB-SAM3U128-V2-NordicSemi 160212.bin file on the bootloader drive but it stays the same. ...
Hi Everyone,
I just purchased an nRF52840 PDK and I am trying to program it via nRFgo. I erased the flash, selected the latest s140_nrf52840_5.0.0-3.alpha_softdevice.hex...
Hello,
My team and I are experiencing a problem with our custom DFU Bootloader, which is based on the Experimental Bootloader Secure Serial example (SDK 13), running in...
Hi,
My SDK version is 13.0 and my problem is when I run the examples\ble_peripheral\experimental_ble_app_buttonless_dfu project the 52DK seems ok but when I use the DFU in...
Hello:
I am setting up my nRF52840 development board to work with the S140 softdevice on Segger Embedded Studio; however, I am running into issues with the flash_placement...
Hello,
I've seen some conversations around the forum for applications that must share the same ID. My application must share SPIMO and TWIMO (ID 3, base addresss 0x40003000...
Hello,
I want to make beacon with my uuids. I am referring to code ble_app_beacon code from sdk 12.2.2
I have made changes according to my requirements in my code.
I am...
Hi, we downloaded the latest version of the sniffer 1.0.1 (today).
We tried that but we could not get it to work reliably?
The application sees the device, we select and...
I am using the nrf51822 with a latching circuit as shown controlled by P0.05 pin.
I am using the following code SDK 10.0 S110 softdevice to Power ON the circuit (PowerPin...
I've merged serial dfu with ble dfu project refering to this post .
I'm getting linker errors stating no space in execution region in .ANY sector...
What could be the...
Hi,
I have add beacon function to "light_control_server" project. I want to every server broadcast their unicast address.
Could do kindly teach me how to do this. It's...
