When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi!
Background:
I'm working on a project where I try to synchronize a wireless sensor network, where the sensors are nrf52 devices. I have gotten to a point where the...
Hi,
I am trying to program an NRF51 DK to read ADC signals at 1kHz with a S130 soft device. I am completely new to programming MCUs and would you recommend using keil or...
Hello,
I'm working with a proprietary chip that has a nRF51822. I want to configure it as a BLE peripheral. I'm using ble_ app_uart example to achieve this.
I tried...
main.c
I am new to nordic devices and currently working on MPR121 touch sensor via I2C on nRF52 device. Using an existing example "twi_master_using_app_twi" as a base,...
Hi
I want to start a new app with the nrf52 to port our app running on the nrf51.
I took as a starting point ble_app_template_s132_pca10040, renamed it, and changed...
Hi!
I get the RAM adjustment warnings when running my nRF52 system:
RAM START ADDR 0x20004000 should be adjusted to 0x20001FE8
RAM SIZE should be adjusted to 0xE018
...
In my application I send a characteristic notification from inside a timer callback function. This causes a restart of my application if I am connected to the board. But my...
It has developed a eddystone-url in nrf52 device based on the current nrf5-sdk-for-eddystone project.
But I would like to know the Nordic's policy about this.
In other...
Hello Everyone,
I wrote the simple software for long push 3 sec and long long push for 5 sec and it is working fine as expected but can anyone suggest me how to create...
Hi there.
I'd like to start measuring the current consumed by a custom board with an nRF51822 on it in various states using a scope. I've read the DK user guide advice...
Hi,
We've developed a prototype for a client and just received the nRF51 chips for production. Problem is that the chips that just arrived is an older revision than the...
Hello, I Preparing the KC (korea-certification. about bluetooth)
KC requirements as follows:
Set Test Modes
Set Continuous modulation mode
Set Unmodulated Continuous...
Hi all,
I'm having a tight deadline upcoming and have run into an anoying problem.
I'm using this NRF51 breakout board: ohtcom.com/.../nrf51-m0-module
I ordered a...
HI I am trying to make 5 characteristics on Nordic and my program does not compile for NRF51822 QF AA or AB. but compiles fine for QF AC. what could be the matter. I get an...
