The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I want to debug RF51822 board by uart port , communicate with pc, e.g use printf() in program,after download RF51822 board,print statement to pc uart port, how to realize...
I am trying to use my nRF52-DK with Yggdrasil.
I took example from here: *\nRF5_SDK_11.0.0_89a8197\examples\ble_central_and_peripheral\ble_connectivity\pca10040\ser_s132_uart...
Hi, I was able to successfully implement the tutorial titled "Testing and using a simple BLE application" available in the Tutorial section and transfer data from termite...
Using OBS-421 from Connectblue as Central. Using simple AT command to connect and get data. Can connect successfully with Cypress BLE as well as the TI sensortag and get data...
Hello,
When i have a bootloader installed and i try to debug application, it doesn't start application probably because debugger programmed application without the right...
hello everybody,
I'm working in a project using the automated generic bootloader example, I want to do some edits so as I can have an input interrupt at any time, I mean...
I am having trouble with the service discovery of my application. When I click Discover Services it takes several seconds to discover all of the services. For example between...
Hello!
I have a problem with ble DFU application upgrade. I use the Master Control Panel 3.10.0.14 under Win 7 on virtual machine and nordic ble usb dongle.
On the firmware...
I used AdaFruit Bluetooth LE shield previously that uses nRF8001. I can define new customer service using nRFgo studio (which only supports nRF8001). I am moving towards using...
Hi,
I am using pca10040 board. i need to toggle a led in 5sec once. I tried to change the prescale value. But im not able to get that much time delay.
Can any one help...
SDK Version: nrf51_iot_sdk_0.8.0_f1f6187
In SDK all examples are given for PCA10028. Is it possible to run on PCA10001?
What I have done so far with PCA10001:
1.Programmed...
Hello,
I have modified the Android-nRF-Blinky Application to use it with the Datathroughput Demo on the nRF52 DK.
The android application runs on a Nexus 9 with android...
Hi, i try to understand how to use mode for supply voltage measurement. But i have a problem and i get always 1.225 volt
hal_adc_set_input_channel(HAL_INP_VDD2_3);
hal_adc_set_reference...
