Hi Nordic Team,
I am trying to implement a secure boot chain on the nRF54L15 DK using NCS v3.4.0 (LTS) with the following configuration:
Board: nrf54l15dk/nrf54l15/cpuapp...
Hi, I have a question with regard to the nPM1100 PMIC and entering ship mode (not exiting it).
If I am interpreting the datasheet correctly, the SHPHLD pin must be held...
Hi Nordic Support,
I am facing an issue where the peripheral registers are not visible in the Keil debugger during a debug session. Only the core registers are available...
Hi:
Use nRF54LM20A_DK.
Use ncs 3.1.1.
And this is source code:
The following error occurred:
« *** Booting nRF Connect SDK v3.1.1-e2a97fe2578a *** *** Using Zephyr...
Hello, I use the NCS v3.3.0 (ncs\v3.3.0\nrf\applications\nrf_desktop). Can the desktop dongle connect to two keyboards at the same time? Development boards: two nrf54lm20...
With SDK 3.3.1 I do not get the <inf> logging messages when building the Hello World app unless CONFIG_LOG=y is added to prj.conf.
Perhaps this is left as an exercise for...
NCS: v3.4.0 Board: custom board based loosely on PAN1783 TF-M not used
Images: - App core: mcuboot, Firmware (main app) - Net core: b0n, ipc_radio
Summary of configuration...
Hello everyone, I was wondering if we could run IPSP over 2 BLE-supported nordic kits and ping one from another without using a BLE-Enabled router, like connecting them together...
Good morning everyone,
I am writing a custom protocol using the RADIO module and I am having a hard time understanding the address organization.....
My protocol supports...
Hi,
I want to interface an analog front-end Device through NRF52840-DK board Using SPI Interface . I want waveforms to be as Below:
which driver I suppose to use is...
Hi,
I try to Toggle ON/OFF the PWM using simple code below.
The PWM does not generate any output.
Please see code below;
/****************************************...
Hi,
I try to Toggle ON/OFF the PWM using simple code below.
The PWM does not generate any output.
Please see code below;
/****************************************...
What is the input impedance or input current of port P0_30/AIN6 when operating as an ADC input? Nominal or typical figures would be OK, but maximum and minimum figures would...
1、Nrf52810 does not have VDD_PA pin, whether it needs software control, whether any pin can be replaced？
2、Is there an example of the use of PA/LNA circuits in gazell and...
Hello,
The Gazell Pairing User Guide in the infocenter states that the AES ECB block is used for encryption & decryption. However, the product specification document for...
I have an issue with bonding between a PCA10040 running the sample Glucose app and an Acer tablet running Android 7 and nRF Toolbox. I have not seen the problem on a second...
Hello sir,
I am a beginner on NRF52840. I am using Nrfx_spim example for interfacing sensor with NRF Board.
I have done some driver about Reg_read and Reg_write. I tried...
I'm using the basic sdk example of ble_app_hrs_freertos example and created two tasks in it, namely Task1 and Task2. Now I have enabled preemption by setting "configUSE_PREEMPTION...
Hello everyone,
I write datas from my Client to my Server, but I don't really understand where I can retrieve my data on my server.
Is this function allowing to get...
Hi ,
What we want is a accurate ms.
below is what we do 1. Set the prescaler config.prescaler = 31;
2.When I need the Elapsed ms, First ,I get the elapsed rtc counter...
