Hello!
I think there is a problem in NCS v3.3.0. nRF54L target, sysbuild build with MCUboot and TF-M, partition layout coming from devicetree (SB_CONFIG_PARTITION_MANAGER...
Hi, I'm developing a keyboard-pcb with NRF52840. I'm doing this as a hobby and are not that experienced with integrated circuits. Anyway, I designed and produced a pcb, but...
Hello,
in cases where the LTE signal strength is extremely low, we observed that the LwM2M /4/0/2 RSRP rolls over from -128 to 127. We found that the nRF Connect SDK uses...
As part of the Bluetooth LE course we need to setup and install the nRF BLE sniffer for wireshark. I have followed the explained steps in the course to set up wireshark to...
The at command documentation says that ENVEVAL is only available in system mode 2 (CFUN=2). Is there a reason why the command can't be run in any other mode? For example if...
Hi
The TWI driver has a twi_clear_bus() function but the TWIM does not.
I'm getting an I2C error, and need to do I2C soft reset. I'm doing this manually at moment but...
I recently completed a field-upgrade path from an nRF5 SDK 17.1 application (with the legacy Secure DFU bootloader) to a fresh NCS-based firmware stack, while preserving user...
In the file app_sdcard.c of the SDK13.0.0, an assert is done when calling app_sdc_init() with a pin P0.0. Can i safely use P0.0 with the assert deactivated or should i use...
Hi;
I am using nrf51822 qfaa device with sdk12.3. I compiled eddystone example code and it worked with nrf51dk(nrf51422_qfac) board. Also, i have a board that has nrf51822_qfaa...
I would like to use the POFCON register thresholds to create a crude battery level indicator. I noticed that the POFCON register definition in the nRF52832 Product Spec has...
Hello everyone,
I'm currently migrating from a functional code IAR to Eclipse GCC.
It compiles fine and I got the hex files.
However I have some troube to flash the...
I am working on an application where the nRF52832 is being used to control external hardware that requires fairly precise timing. Specifically, I use sd_radio_request to allocate...
Hello.
I want to develop a custom bootloader with the same purpose as described in Very simple SPI bootloader
I'm using a 52832 with Eclipse/GCC and nRF SDK V13.0
...
Hi there,
I've tried using PCA10040 with NRF Connect to do Secure DFU but no luck. Any idea on how to get it recognized, please?
I'm following this:
infocenter.nordicsemi...
In the Bluetooth Light Controller example for the client, in provisioner.c this beautiful comment can be found:
/* Provisioning encryption key storage (this is not how...
Hi all,
Here is my first question on this forum after many hours working with the NRF but for the first time I didn't found the answer :)
My problem is :
I would like...
Hi,
We have custom board with STM32F407 as an application chip and BL652-SC-01 as a connectivity chip. When we worked on SDK 13 and softdevice 4.0.2 or 4.0.4 we had problem...
Hi, I have problem with using printf() in SEGGER RTT.
I've read tutorial and others about SEGGER RTT printf() problem, but they didn't work.
When I use printf() in RTT...
hi,
I found ble_app_multilink_central example under SDK but this is for LED button application.
Is it possible to configure the same example for NUS?
I worrying about...
I have app (based on buttonless_dfu) works on sdk 13, sd 3, nrf52832.
Now I try to migrate this app to newest SDK14, sd 5.
I can't resolve one issue. I have main.c and 7...
hi, I found ble_app_multilink_central example under SDK ,and make it work with NUS. Some problems bothered me.
When the amount of data reaches a certain amount, the transfer...
