Enabling coded broadcast compilation may result in undefined coded parameters, and coded scanning may also generate errors. May I know which SDK version will support these...
Hello,
I using ncs v3.1.1 SLM on nrf9151 to send messages to a CoAP server. It seems nrf9151 by default uses AES_128_CBC_SHA256 even though on the server side, we have given...
Hi, I am unable to read GPIOs (always getting 0x00000000 from gpio_port_get or 0 from gpio_pin_get). My main project is https://github.com/marcuswu/leaf-fall/tree/main/firmware...
The DECT Nr+ shell (the MAC version, not the -phy; tested with v3.3.0-ba167d9f3db4) offers IPv6 connectivity.
The DECT standard has a profile for IPv6 described in ETSI...
Hello,
Overview:
Currently we are using nRF9160 we are using mbedtls library for generating EC key based certificates (self-signed and CSR). Our code is built with TFM...
Hello, I wanted to update my project (Custom board using the nRF54L15 ) to the v3.3.0 SDK since this fixed a BLE bug with the v3.0.1. version. To my knowledge I did not change...
I have installed ncs3.3.0 and want to keep ncs unaffected. According to the document docs.nordicsemi.com/.../sdk_setup.html , I should choose to import the edge impulse SDK...
Ciao all,
Two weeks ago I have started to learn about beacons and their usage. I have bought pca10040 development kit and designed custom nRF52832 based beacons. After...
Hi,
I've just hit a strange issue with SDK 12.1 on nRF52832.
Usually on BLE_GAP_EVT_DISCONNECTED , sd_ble_gap_adv_start gets called to start advertising and everything...
I am new to nRF 52. Previously i have worked on arduino IDE for programming arduino uno,mega. I have also used MPlabX for programming PIC(MircoChip) series micro-controllers...
Hi,
For the NRF52832, I read that a number of write (per block) is limited before a forced erase of the page. Apparently, the amount of write is 181 times for a block of...
My sensor app is based on nRF UART service and my current case in one sensor (peripheral) one gateway (central).
In a situation where there are two pairs of sensors (S1...
I'm trying to use a low accuracy GPIOTE event to start RTC1. The following code works as expected when using hi accuracy mode but will constantly trigger in_pin_handler()...
Hi, I am using radio with ppi to advertize packets as shown in the mainc file attached. mainc.txt
Even after allocating the access address of Bluetooth on line 196 as set_address0...
Using nRF52832 I am collecting from 8 SAADC channels using example ble_app_uart__saadc_timer_driven__scan_mode as a guide. AIN3 (P0.05) gives incorrect results. Because P0...
Hi,
I have an application that utilizes the dual bank bootloader and s132 soft device on the nRF52832 chip. I am trying to determine the total RAM used and can't seem to...
Hi,
i am using NRF52 and S132V2.0.0 SDK11. i am working on BLE application in which i implemented DFU service to it, so that i am able to observe DFU service and 3 characteristics...
Hi
I use SDK version 12.2.0 to do a project. I add two 128bit uuid into my project. The one of 128bit uuid is created by myself. The other one of 128bit uuid is used ancs...
Hello,
I wanted to check the log on nRF52 example codes. Though the code compiles and runs (GCC compiler) I do not see the log anywhere. I tried connecting the device ...
Hello,
I was going through the schematic of PCA10040 and I see that the nRF52832 is interfaced to an ATSAM3U2CA-AU. I was under an assumption that nRF52832 itself is a...
We have a custom PCB with the nRF52 MCU.
Our application uses BLE. Thus, we need to program first the SoftDevice. In our case, we are using nRFgo Studio.
Normally, when...
