Hello,
I have 2 Memfault projects that I'd like to rename, but I can't find any way to do this through the web app, and the API authorization keeps getting rejected (tried...
Hello, I'm working on a prototype device based on the nRF9151 DK.
HW: nRF9151 DK, nRF9151 LACA A1A Tested with modem_shell sample app, NCS v3.4.0.
Symptom: on boot, "The...
Hi, I have a question with regard to the nPM1100 PMIC and entering ship mode (not exiting it).
If I am interpreting the datasheet correctly, the SHPHLD pin must be held...
Hi Nordic Support,
I am facing an issue where the peripheral registers are not visible in the Keil debugger during a debug session. Only the core registers are available...
Hi:
Use nRF54LM20A_DK.
Use ncs 3.1.1.
And this is source code:
The following error occurred:
« *** Booting nRF Connect SDK v3.1.1-e2a97fe2578a *** *** Using Zephyr...
Hello, I use the NCS v3.3.0 (ncs\v3.3.0\nrf\applications\nrf_desktop). Can the desktop dongle connect to two keyboards at the same time? Development boards: two nrf54lm20...
With SDK 3.3.1 I do not get the <inf> logging messages when building the Hello World app unless CONFIG_LOG=y is added to prj.conf.
Perhaps this is left as an exercise for...
Hi all,
I would like to use the Arduino programming environment on my nRF51422 prototype. I have seen that RedBearLab has done the migration for the nRF51822 which quite...
Is the nrf52832 developer kit compatible with Arduino Leonardo? I know that most Arduino shields work well with Leonardo, but a few have troubles.
Thanks
Hi,
I would like to have a recommended supplier for the 32MHz crystal. I have seen the specification for the crystal. But from my experience it is a bit more complex than...
I followed the guide of this and when I opened the project " BLE_Gateway" ,it showed that the "spi_slave.c","softdevice_handle.c"and "ble_advdata.c" file couldn't be found...
I can not compile the example project 'ble_app_uart_s132_pca10036' ,in nRF52_SDK_0.9.2_dbc28c9\examples\ble_peripheral\ble_app_uart\pca10036\s132\arm5_no_packs.the error given...
I have a fully working project that uses the HomeKit SDK 1.0.0 from Nordic Semiconductor.
In order to be compliant with Apple specs I am trying to upgrade to version 2.0...
Hello,
I enabled debugging in keil v5 for the nrf 52 and I am debugging through UART for the ble_app_proximity and viewing the messages in putty. The messages i received...
hello everyone,
I was trying to turn off nrf51822 on some condition. So i thought i will use systemoff mode register to do that.i am attaching code snippet of what i am doing...
I am trying to build the ble_app_hrs using gcc. It seems to build okay. I can program it to the device. When I press button 0 or any of the buttons the leds does nt light...
Hey All,
Just trying to get some advice/examples on how to incorporate notifications into a Custom Service on a nrf51 Dk board using gatts. I have found a couple of examples...
Hallo everyone. I'm working with the processor nRF51422 with S210 softdevice and I would like to ask you if it's possible to drive results of LPCOMP to a General-purpose I...
My goal to build a device that can connect to phone with nRF8001.
I am using nRf8001 Development kit. My prototype uses TI msp430 with the nRF270 board in the kit, and I...
Hello,
I am using a Windows 7 VM (VirtualBox). I can flash my NRF51 DK using nRF Go Studio just fine.
When I open the Master Control Panel (3.10.0.14), I can see the device...
