Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hi, I used the sample code "Master Emulator->2.1.7.8226->Example code->nRFUart"
to develop a new project, and encounter some questions...
we update nRF6310...
Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
I'm a beginner of BLE and I did everything from the three BLE tutorials, that uses sdk 11. However when I try to do it in sdk 12.3 it doesn't work, because there are...
Hello,
I am using ble_app_uart code. My first goal is to execute a function when board connects with an android device. Another goal is to disconnect board from an android...
When reading about access_opcode_t struct on its infocenter page it stumbled upon this table i don't understand.
access_opcode_t is defined as:
Data Fields
-------...
I'm employing 51822AA.
I need to debug firmware for this chip line by line. Like environment of ARM9 with Lauterbach TRACE32 through JTAG.
Is line debugging possible...
From application point of view, when should I use UICR and when should I use Flash storage? I have studied the documentation and the functionality seems very similar. The...
Hi everyone,
I trying to make a flash jump on Nrf51822 in my project. there are 2 programs(program A and program B) below. i am working on to make program A jump to program...
Hi everyone,
I'm new with nrf52832, and I need to measure elapsed time in microsecond between rising edges of 12 different Gpios. I have 12 piezoelectric sensors filtered...
Hi,
I have used nRF52840-PDK.
And I want to test profile and protocol with PTS.
I succeeded in GATT-based service test and GATT test with PTS.
But when I try to L2CAP...
How do you do
Now use the Nordic \ nRF5_SDK_12 2.0 _f012efa \ examples \ ble_peripheral \ ble_app_uart this plus Nordic \ nRF5_SDK_12 2.0 _f012efa \ examples \ peripheral...
I try to add default nRF sdk libs in Segger studio. All files exist and path corect.
in nutshell i try to add uart module to default ble_app_buttonless_dfu example
Hi ,
I'm looking for BLE Specification but I just found NRF52 Datasheet on Nodric page . Can you give me this document , It will help me a lot . Regards !!!
Hello All
I am planning interface the BLE peripheral + Capsence(Atmel QT111) board
i did the Capsence Board with Spi Protocol..then second phase i has to implement with...
Hello
I have some problem that I want to change Characteristic UUID different from Service UUID.
Like,
Service UUID : 11111111 - 1111 -1111 -1111 -111111111111
Charcteristic...
Hi Nordic,
I used FDS to operate updata to update data more than 10K once, but there was an error. Hint FDS_ERR_RECORD_TOO_LARGE.Can FDS operate more than 10K data at once...
