hello, im from india im using nrf24l01+ for my project to transmit and receive data between two arduinos. i tried all tutorial basic programs but i cant sucessfully send and...
I'm analyzing app_timer scheduling code..
I have an question about list_insertation_handler function in SWI0_ISR
I think if ( (p_timer->ticks_at_start - m_ticks_latest...
I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hello,
I'm testing PHY coding (for long range), I'm pretty surprise from what I get when I scan the RSSI of bluetooth channels (with Nordic app).
This is my set up:...
i want to erase and store the flash after detecting the radio active.
The radio signal is also active, when i erase and store .
Do erase and store the flash may influence...
Hi there,
I try to using nrf sniffer for trouble shooting, and follow the "nrf sniffer user's guide v2.0" , when I copy the unzip extcap's content to the Wireshar's Extcap...
Hi!
i am thinking about cut off uart when data is not transmitting.
As a method 1, i am thinking about using CTS and RTS Pin which is hardware flow control!
①Is this possible...
I'm using the nRF52 DK with mbed, running the heart rate monitor demo app.
When I disconnect the board from the PC and attach a USB power supply instead, the nRF52 won...
Hey all,
I'm working with the nRF51822 (nRF51dk) on a mac running high sierra, and I've been following this tutorial to try to get started. But when I try to make flash...
Dear Nordic engineer,
I try to setup Wireshark sniffer with nRF52-DK. I followed by nRF sniffer user guide v2.0.
I see interface toolbar of nRF sniffer on Wireshark. But...
Is there a block header information available that I can read thru the flash read function (e.g. in ble_flash driver, ble_flash_page_read() function ) ?
My FS (file system...
Hello,
I would like to understand the reason behind getting a error,(0x04) NRF_ERROR_NO_MEM , when calling the function
sd_ble_gatts_characteristic_add(p_service->service_handle...
I'am realy new to nRF52 development. I want to start with a simple demo as shown on www.nordicsemi.com/.../Getting-started-with-the-nRF52-Development-Kit.
What HW do I...
Every time I change a common source file within Kiel, the source file is changed for every project because (obviously) is a file common to all example projects.
Is there...
Is there a nordic guide which lists out the steps taken by the chip when going though a bonding process? I am trying to add as many RTT printouts as possible to know where...
finally I have done to implement that ADXL345 can throw data over BLE using nRF UART app service with this code . now my problem is how to change 2's complement ADXL345 data...
Hi,
We are using a nrf52832 in a serialized application with a STM32F4 and standard SPI as the transport layer. We are using the SDK V12 on the STM32 and softdevice S132...
Hello,
I want to add DFU fonction on my custom application. The final goal is to update my firmware from my custom app (not just once).
My setup is : SDK11 - nRF52832...
