I am using esb in SDK 11 and my understanding is that the radio causes interrupts that are forcing and cannot be disabled. These in turn causes software interrupt 10 to be...
I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
I'm curious about the CPU lockup reset. We have a long term test with 9 units running identical firmware on identical hardware; line powered, running continuously for 6 months...
Hello,
I have a problem with turning on notification on a characteristic so I can start receiving data.
I am using a nRf51 dongle as a client device, using softdevice...
Hi, I would like to establish services with following security permissions in a Bluetooth 5 peripheral: Currently I use the NRF52-DK and SDK 15.2 Service A: Security level...
I'm trying to adapt the secure_bootloader example for our custom board with a nRF52832 QFAB with 32kB RAM and 256kB Flash, following the information in this thread:
https...
I'm building a project on top of cli examples:
<SDK>\examples\peripheral\cli
<SDK>\examples\ble_central_and_peripheral\experimental\ble_app_interactive
My goal is...
Hello
I need to setup the the PWM peripheral@ 8MHz with one selectet Channel in DMA mode. For development, I am using the NRF52840 Preview Dev Kit PCA10056 (Q1AAAA). I did...
I have one question, if Nordic can give some confirmation, that Nordic chips can be used together
with Murata XRCGB32M000F1H00R0.
Customer just asks for that I don’t...
Hi,
In my project NRF51422 need to communicate with two peripherals which are supporting only UART communication.
please help me if there is any possibility.
Thanks...
I'm use the app_button lib to deal with button event ,things go well, I assign the push ,release and long push event to button event .
But there came a situation,while the...
I have noticed that when I run in release mode, turn WDT on, write bonding info, clear bonding info, and reset, my application suddenly uses 2mA more and takes 5 minutes ...
Hi all:
My iOS app use iOSDFULibrary to update my ble.But when the device enter into DFU mode ,it disconnected for a while.
This is my log:
2018-11-27 21:00:11.122263...
Hi Nordic.
Now I am working on a BLE smart card and am adding an external power amplifier. For low power consumption, i decided to give power only when I want PCB doesn...
Hi,
I tried to use nRF52 evaluation kit to program my custom board for that I have used Debug port P19 in evaluation kit. It was working in the beginning but after sometime...
Hello,
I tried to follow the instructions in this tutorial: github.com/.../nRF52832-buttonless-dfu-development-tutorial
1) I flashed this file via nrfjprog: examples\dfu...
