Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Hi. I am running Thread on 9 nRF52840 nodes. I am able to ping as many packets as i want but am failing to send pings every fraction of a second. I want to send pings in just...
HI：
when i use NRF MESH 3.0 lastest SDK, Compiling one of the examples will prompt the following error. It's should be lost flash_palcement.xml file.
Building ‘dfu_nrf52840_xxAA_s140_6...
We have vibrator connected to gpio pin 18 on the nRF52832. Controlling it works fine in the application but as soon we enter DFU the vibrator starts and it doesn't stop until...
Dear Nordic Team,
Is it possible to use the nRF52832 for MCU application only, without the BLE stack. Can the application code use the complete memory of the nRF52832. ...
hi.......
i am facing the issue while i am transferring the data via ble to ble_app_uart ...
i am using nrf52382 and segger 15.2v
Here if send the one data over ble...
I use SDK12.2.0. The mobile phone has connected my 51822 device,and then the mobile phone keep away from my 51822 device till to disconnect.how to do that they will connect...
Hi Guys,
I facing issue on one of my project, our HW require 2 set of TWI and one QSPI/SPI. I notice SPI0/1 cannot be used because I need both TWI0 and TWI1 to be supported...
Hi,
I'm trying to adopt my nRF52832 projects to the nRF5 SDK version 15.2.0 and the NRFX drivers framework. I'm using a short app_config.h with NRFX_RTC_ENABLED and NRFX_RTC0_ENABLED...
Hello,
There is a example for the nrf52840 for thread with mqttsn. Although this is just for my personal use I would love to use some kind of encryption for it.
So the...
Hello. I have been trying to work with extended advertising between two nRF52840 boards using the SDK, but have had trouble in setting a long advertisement payload (as in...
I followed Einar's nRF52840 Dongle Programming Tutorial and tried the ble_peripheral/ble_app_eddystone example using SES 4.12. Opened the project, changed the preprocessor...
Hello All,
I have been using this NRF52 DK board with KEIL for like 2 weeks. I read the all the document regarding BLE 5 protocol and followed the DIY codes step by step...
