hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
Hello,
The question might be a little vague at the moment but I would like your guidance if possible.
I already asked other questions related to this topic but I will...
Hello,
I have been seen some resets on my softdevice v3(SDK12.2) that I am unable to understand,I am using the FPU as well as pheripherial as SPI, I have set up SystemView...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Does increasing the sample time on the SAADC increase the accuracy of a single shot measurement on the SAADC? I couldn't find anything in the datasheet regarding accuracy...
Hello,
I would like to use nRF52810 chip.
And I want to implement PCB trace antenna and PCB chip antenna on same PCB(for provision)
Either PCB trace antenna or PCB chip...
I am using the SPI peripheral for communicating with a network through long wires. Is it any information about the impedance of the driver outputs from the nRF52832?
I will...
nRF52840 OPS v0.5.1 section 16.16.2 states “A pin reset is generated when the physical reset pin on the device is asserted”. This seems to contradict the descriptive name...
Dear Nordic
All our last SDKs in "example/dfu" have same error.
Code is not corect:
nrf_clock_lf_cfg_t clock_lf_cfg =
NRF_CLOCK_LFCLKSRC;
Impossible properly...
Hi Nordic Support,
According to the answer in question:
devzone.nordicsemi.com/.../
it is not possible to update the bootloader (which is the case with "bootloader_secure_ble...
I am trying to set up RTC2 by following an example
github.com/.../saadc_low_power
I ported it to my project which is running a softdevice on nRF52. It works perfectly...
Hi Alls,
I'm trying to compile and test the example project from SKD_12.3.0 and receiving the following error:
#error app_timer for freeRTOS requires configUSE_TIMERS...
Hi everyone
I'm doing some basic test to verify the correct platform for a future project, we need ble long range, therefor we are testing the NRF52840-PDK
I have loaded...
hello,we use nRF24l01+ for the communication of IoT.There are a lot of terminals work at a same channel,when the controllers send CMD,we have found:the length of reading from...
Hello,
I am having a weird reset behaviour with my nrf52832pca10040, SDK12.2 with softdevice v3.
I have connected an acc into the SPI interface through these pins
...
