Hi I'm testing the current consumption of the external qspi-flash on nrf5340dk [ MX25R6435F]. I have used ppk 2 to measure consumption with the dk and also have used a power...
Hi,
We are using nrf21540 in GPIO mode + mode pin ( and CONFIG_MPSL_FEM_NRF21540_RUNTIME_PA_GAIN_CONTROL) with an nrf52833.
We are developing under nrf connect sdk 3.0...
During the development of a Matter over Thread product, I encountered the following issue:
After adding two Matter over Thread devices (an OnOff Switch and an OnOff Light...
Hi Nordic Teams :
I would like to check the current consumption by BLE DTM.
1. Is the table measurement is from 3.0V input?
2. I find the condition in the datasheet...
HI ALL,
nrf54l15dk,v2.8.0,peripheral_uart demo and no changes have been made.
Then add the following content to prj.conf
sysbuild.conf
mcuboot.conf
At this...
I'm developing my application with nrf 52832 and nrf SDK v17.
I know NCS is more powerful. I'm currently learning how to use it.
But now.I still need my application with...
I'm writing a wav file from the nrf52840 board to the nor flash w25q128jv with a capacity of 16mb but it seems that I can only operate on the first 2mb, even when dividing...
Hi,
My application receives assert error from stack. Source file name is src\ll_master.c, line number 831 and error code 0xDEADBEEF.
What this error signifies?
R...
Hello,
In my application I'm using SDK 8.1 with the s110 SoftDevice. In the new version, the pstorage modules have been separated and you need to choose between them.
...
Trying to see how much time my code consumes, I tried the naive approach, calling clock() in the beginning and at the end and comparing the values.
But when I include clock...
I am using the BLE Scanner app on Android to check that my device works.
I have 2 similar problems :
on one device, I can read all characteristics except one. This has...
Hi,
Im trying to use this example to send serial data from GPS module via BLE:
github.com/.../ble_app_uart_low_power_slave
I have disabled hardware flow control since...
Hi
I tried gateway and LED_mesh examples. It worked well. But, I found some issues as below.
When I tired MCP windows application on laptop with PCA10031 dongle...
Hi there,
I am using the nrfjprog to flash the nrf51822 via a J-Tag programmer. Here is the command I used in the command prompt:
nrfjprog --eraseall --programs softdevice...
Haw can I configure ble_app_ uart examples for bonding using? I want to connecting, transmit and receive data throw the UART only with 5 fixed devices.
Hi,
I updated to softdevice 8.00 recently, and found something different with softdevice 6.00.
When trying to program the new softdevice hex to the chip using nrfgo studio...
Hi,
I am using nRF51822 chip.
I am using the softdevice s120_nrf51_2.1.0. On top of that i am flashing the HRM central example given in the SDK nRF51_SDK_8.1.0_b6ed55f...
Hello, I'm fairly new are Nordic and have inherited a good project from a departing coworker. We are using Keil uVision 5+nRF51822+BLES110 softdevice.
She explained her...
Hello,
As mentioned title, when using printf with softdevice, "Stopped by a vector catch" occurred.
I am using my custom board(nRF51822 and s110).
And I am using IAR...
Hello,
When i try to set value of the gpregret using sd_power_gpregret_set and clear functions in on_write callback function, cpu gets stuck (i check it in debug mode). Can...
Hello
I'm trying to communicate with an sensor over the TWI HW interface during a BLE connection with the S110 soft-device, and every time I try to use the TWI bus the...
