Hi
Are there any examples of a custom board for nRF54L15?
I have a project built/running on the nRF54L15 DK.
I now want to create a custom board for the nRF54L15.
...
Hi, i am learning with thingy 91 x and nrf9151dk. I made the online courses and succesfully conect to the cloud with the nrf desktop quick start in both devices. Now, i would...
Hello,
I am working with a custom board that has the nRF52840 (via the ISP1807-LR-RS module). This board has the SIT1552AI-JE-DCC-32.768E MEMS TCXO. This TCXO chip has a...
It would be extremely useful to get the HCI Traces (BLE) of my nRF54L15 boards. Documentations: Embedded HCI Tracing For simplicity's sake, here is my setup: - nRF54L15DK...
Hello there,
I'm designing a set of devices composed of a remote and 2 peripheral. The remote's job is to be connected to the 2 peripherals as a central and occasionnaly...
Hello, I’m testing a PID controller for a quadcopter. When I compile the application with the optimize for speed then flash, I notice that the PID response is slower than...
Hi,
I have a couple of questions regarding reading the nRF5340 Temperature Sensor. This is a follow-up to the following DevZone ticket: https://devzone.nordicsemi.com/f...
The macro NRF_DRV_SAADC_DEFAULT_CHANNEL_CONFIG_DIFFERENTIAL does not set the .burst field in the nrf_saadc_channel_config_t structure.
The macro NRF_DRV_SAADC_DEFAULT_CHANNEL_CONFIG_SE...
The app_fifo support e.g. in SDK 12.1.0, appears to have a serious problem when the read_pos/write_pos values wrap. i.e. when the fifo has been used over a period of time...
I have BLE400 extended board for nrf5. It has cp2102 on board from Silicon Labs. I installed drivers for mac and can see NRF_LOG_INFO via terminal. It would be great to have...
i am using nrf52840 with sdk 13.0.0-1.alpha. I want to boot the application from bootloader but by
using UART as a transport layer.
Would you plz help me?
I found end of address of fstorage from macro of "#define FS_PAGE_END_ADDR (fs_flash_page_end_addr())". But I want to change the start address of fstorage. Which macro or...
I have multiple GPIOs that are configured to use GPIOTE in my application. When one of these GPIOs is in the active state I start timer. Once the timer expires I want to enter...
Dear Nordic Team,
Thanks for supporting.
Currently i am try to work with VL53l0x distance sensor. Basic communication working good, but i am not able to get distance...
Hello
I tested a BMD-300 Module and Nordic Team has been very helpful.
I tried to reach the maximum speed in this module.
I like to send 4x20 byte per 30 ms, but I...
Hi all,
I am using as base the Experimental ble_app_blinky_central and ble_app_blinky examples.
I noticed using a sniffer that the Central is asking to the peripheral...
Hello,
I am going to us the meander antenna from the nrf51 usb dongle. Are there any drafts with correct dimensions? And second what should be the minimum distance between...
I've been through the tutorial of connecting the NRD52 board to my PC, but my PC isnt recognizing it at all. No pop up for any usb devices. I've tried different cables and...
Dear Nordic Team,
Thanks for supporting.
currently i am try to interface MMA8453 accelerator with ble proximitty example .Already i have interfaced peripheral example...
Hello, I am new to NRF. and actually i dont have other MCU experience, beside adrduino.
my question is not about BLE/BLE+,
it's more about how to use NRF5283 in keil question...
SDK 13 Alpha
The header guard in serialization/connectivity/codecs/s132_s140/serializers/ble_l2cap_conn.h looks like this:
#ifndef BLE_L2CAP_CONN_H__
#define BLE_L2CAP_CON__H__...