We encountered some problems while debugging the nRF54L15. A total of 10 circuit boards were produced, and the chip on the board is nRF54L15CAAA. After programing the code...
Issue:
I would like to bring to your attention that I am getting an error when running the 'list command using the nrfcredstore cli utility, while trying to retrieve the...
Are there any migration guides for a customer who wants to migrate from nRF5340 to nRF54L15? And if they are nRF54L15 in chipscale, anything they should be aware of including...
Hi,
I have been playing around with the configs but I could not get Mode-3 to activate. What should I change for cs configs and the prj.conf file in order to activate it...
Hello - We're designing a new app for our product in Flutter. I was writing the proof of concept for the firmware updates, but I hit a roadblock with a Mcu Mgr Error: 25 ...
Hi there,
I am using an NRF54L15 custom board and am trying to set up a functionality using DPPI + PPIB. using a single in (1 event) and single out (1 task). I have two...
Hi,
I'm trying to get the debugger to work on my target board. I created the attached simple program to eliminate complexity.
The debugger starts, but it starts running...
I need to change the flag of the scanrsp. I use the advertising_init() and i try to do like this:
scanrsp.flags = FLAG;
but the function ble_advdata_set(&advdata,&scanrsp...
Hi,
I'm tring to generate private key of dfu, but it didn't work fine.The following is my steps.Did I miss something?
C:\Users\Administrator>cd C:\Program Files\Nordic...
I'm trying to tune a chip antenna for nrf52832. I am not an RF engineer but have figured out how to get the basic VNA measurements done.
I've been fighting with finding caps...
Are there any dirty hacks to pass a little data, like 1 bit even, during pairing?
I need my central to tell the peripheral orientation, left/right, as early as possible....
I am using an nRF52832 PCA10040 board, using s132_nrf52_2.0.0_softdevice.hex, and have AIN0 connected to a potentiometer similar to this . The power input pin is connected...
I am using a eeprep tool which can only be used with command prompt. I am struggling with it.
Here is the format to use eeprep tool :-
usage: eeprep [options] <infile...
Hello,
So — in just trying to get the blink example working, I've come across all kinds of toolchain weirdness. I'm using CrossWorks, because it's on OSX and it's way cheaper...
Hi all
Is possible from softdevice or from program application edit the GAP service? I know this service is mandatory but what about edit the structure which is shown on...
Please give me a professor.
In the nRF 52832 sample project, there is an NRF_LOG_INFO function, is this the ability to output a debug string to the UART?
If so, how can...
I have custom service, where I have declared 2 handles inside BLE Service structure, one for button action and the other for custom battery ADC measurement, each identified...
Hi,
I have seen similar questions to this, but I could not make it work.
I am trying to upload a new code using DFU by means of a smartphone (using nRF Connect) or PC...
Hi. I just noticed this bombshell in the release notes for v13.0.0-1.alpha:
Dropped support for nRF51 Series devices.
Although this is preceded by:
...
Hello ! I am trying to implement a write request but for unknown reason it doesn't transmit back the gatt_status. I have setup the wr_auth = 1. GPIO number 19 si actually...
Hi, I want to add DFU to ANCS example.
I use SAMSUNG GALAXY Note5, nRFToolbox, SDK 11, nRF52832, softdevice 2.0.1.
Bootloader project I use is : nRF5_SDK_11.0.0_89a8197...
