Hi, we are developping a medical device that receives an audio stream from a smartphone. We have a custom board connected to a different DSP than the one in the nrf5340_audio_DK...
Hi! We're testing nRF7002 with the nRF7002-DK and NCS v3.0.2. CONFIG_NET_ZPERF=y has been added to the nrf/samples/wifi/shell/prj.conf, the rest is untouched. Running that...
I am using the nrf5340 on a nrf7002fk dev kit. I am interested in low power operation so I am measuring the power consumed.
I am running a simple app:
int main(void) ...
Hi,
I have a simple question about Bluetooth Channel Sounding:
Question: If I use BT_CONN_LE_CS_MAIN_MODE_3 as main mode (PBR + RTT), does it make sense to use sub mode...
Hello Nordic Team,
I am currently working with the NRF54L15-DK. I have successfully configured the simple ADC on AIN4 (P1.11) and am able to read the raw sensor values....
i am writing data from wav file to w25q128jv and i got error -22 at some offset while writing. i tried many config but it seems the problem is not solved, does anyone have...
Hello Nordic Team,
I am currently working with the nRF54L15 DK and interfacing an occupancy sensor over UART. In my standalone application (non-Matter), the UART communication...
Hi,
IAR ARM 7.60.2
Nrf52
Softdevice 132 v3.0
SDK 11
I am trying to use SPI with easy DMA. I have implemented the PAN 58 workaround for sending 1 byte but it fails...
I got started with bluetooth learning. But it's too hard to understand ble protocol. Do I have to learn BLE protocol even If my purpose is only ble communication with simple...
Hi,
Could someone help me about the following questions?
Q1: What are the connection parameters set by the Android app nRF Connect? Can I change them?
Q2: How can...
I have a bit of a strange problem.
I am designing a signal Gazell signal repeater.
It listens in host mode then sets itself as a device to pass the data along.
However...
Is it possible to put the nRF52 into recieve only mode (say through direct test mode) so that the input impedance can be measured using a VNA? Is the input impedance of the...
When I initialize PPI after timer1 has been initialized I get a fatal error (and reset).
Code:
const nrf_drv_timer_t timer1 = NRF_DRV_TIMER_INSTANCE(1);
nrf_ppi_channel_t...
Hello,
we were measuring sleep modes and it consumes around 1.3uA which is correct.
But when we needed to be woken up on edge we found out it consumes extra 8uA! Are you...
Are there any nRF51 demo firmware implementing paring function that the central and peripheral devices will connect automatically without user interaction when they come ...
i am working using NRF52, s132, sdk11, freertos.
for fft , i used "arm_rfft_fast_f32(...)" in cmsis-dsp library.
and i inserted a fpu interrupt.
NVIC_SetPriority...
Hi.
I'm using PCA10040.
I'm trying to control GPIO.
But I can't control PIN 09, 10.
Let me show you my source code.
int main(void)
{
/* Configure LED-pins as outputs...
Hello!
I have encountered an interesting issue:
When I use compiler flags (GCC CFLAGS) -Os or -O0 together with -flto the pstorage function pstorage_block_identifier_get...
After I combined the Timer example and ble_app_uart, the program is hanged at below function when init the timer. Please tell me why
__STATIC_INLINE void nrf_timer_event_clear...
I need to turn off a GPIO after 8 hours of it being triggered.
I was reading about changing the prescaler to allot for 8 hours. I did the calculations and came up with a...
