Hello,
I have a device based on nRF51822 revision 2 and SoftDevice S110 v7.1.0. Because it is revision 2 it is affected by PAN44 and PAN45, and by default the SoftDevice...
Hi Guys,
I know this is more for software issues. But I was curious as to where I can find trusted case providers/makers for the nrf51822 Beacon. Can anyone from the community...
Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
What is the best way to start a new nRF52 project, on a custom PCB?
I have a custom PCB, with nRF52 module. I use IAR, with ST-LINK V2
Say to test the GPIOs, do I start...
I took a look into the PCA10040 and the differences from PCA10036, seems to be minimal...
NFC connector and some breaking points. My question is: if somebody from Nordic...
Hi,
I am new to the nrf52. I want to implement the code that gives me current date and time value based on default set values.
for this i need to read the current counter...
Hi
Any ideas how best to implement a combined iBeacon and standard advertising device (both devices are active at the same time) ?
The iBeacon has to send an advertisement...
Is there a way to generate a DFU OTA image from OS X natively without having to use a Windows platform? It seems that the missing step is dat file generation and json manifest...
Hello guys,
Firstly, i would like to apologize if this post doesnt belong here. But i couldnt find any other platforms anywhere else for me to ask this question. So i have...
hi .
i did what this linke says
but it get me these error
..\main.c(632): error: #20: identifier "NRF_CLOCK_LFCLKSRC_RC_250_PPM_TEMP_8000MS_CALIBRATION" is undefined...
Hi,
I've got some really simple code I've been trying to get working with SPI on nRF52 (while also using SoftDevice):
///MISO, MOSI, SCK set, but SS not
err_code =...
I am trying to figure out if I need to disable the softdevice to get the power numbers in to the single-digit uA range.
With the softdevice loaded/enabled, but with the...
I'm developing nRF52832 to implement the Eddystone (※ 1).
But i'm thinking seriously about what can I do to have the Eddystone Specification and compatibility.
please...
I am working with the ble_app_buttonless_dfu example and am wondering why the example sends 2 notification messages in response to a command being written to it? This occurs...
Hello,
I'm using nRF51, SDK10, S110 beacon example with dfu service.
What I have done are listed as below:
merged softdevice8.0 and bootloader to sd_bl.hex and...
hi,
in FreeRTOSConfig.h file,
#define configUSE_TICKLESS_IDLE 1
#define configUSE_IDLE_HOOK 1
and the idlehook function
void vApplicationIdleHook( void )
{
__WFI;...
I have got PCA10040 development board having nRF52832 nordic ble chip. I am not able to get datasheet for this. I have to use SPI communication on this board but I am confused...
