Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi, i've just started to use the nRF8001, so forgive me if this is an obvious problem.
i'm using the nRF8001 with a microchip PIC processor.
i'm using the ace_tl_demo...
Hi,
I have read ANT Message protocol and Usage and tried to implement shared channel according to section 8.2. I am using nrf51422 and S210 and SDK 10.0.0
My master...
I'm trying to use TDD for my development of a BLE peripheral application, but I'm running into some problems. I'm using Ceedling, CMock, and Unity for my TDD environment,...
I'm trying to scan beacons. This is what I added to the example ble_app_uart_c :
case BLE_GAP_EVT_ADV_REPORT:
{
const ble_gap_evt_adv_report_t * p_adv_report = &p_gap_evt...
Hi all,
I have a problem in architecture of my application based on SD132v3 SDK12. It should interact with an iOS device as a peripheral and receive some data to display...
Hi,
I am using NRF51822 and SDK11 with S130. I have enabled WDT with 2000 as reload value as I'm using 1 second timer. But I want to immediately reset when a certain condition...
Sir,
We are using your radio component in our system since many years. We are in the process to get conformity with Japanese rules.
The lab in charge of testing is asking...
Hello,
I'm trying the ota tester with pca10040 board however the ota tester won't run.
System hangs around softdevice_enable() and goes to app_error_fault_handler. ...
In Android 5.x (API 21) and up, we are experiencing a problem with our BluetoothLeScanner, on some Samsung models like S4 Mini and S5 Mini.
More precisely, an error is being...
Hi,
I would like to use assembly language instructions for the following piece of code:
nrf_gpio_cfg_output(PIN_EN_BSTR);
for(int i=0;i<NUMBER_OF_SHORT_PULSES_TO_TURN_BSTR_ON;i...
Hi,
I wrote a function setting some GPIO pins, initiating an SPIM transfer (with EasyDMA), then waiting for the SPIM handler to signal end of transfer, and then set some...
HI,
I am using nrf51822 to communicate with ADT7320,using nRF51822 as the master,and the ADT7320 as the slave.I used the SPI master example,then i want to get temperature...
I've not been able to program the nRF51822 using the Blackmagic probe programmer because the nRF51822QFAAH1 seems to use a previously unseen device code of 0x008F
Could...
Hi guys!
Got a problem with re-initialising my SAADC to read my current battery voltage. I'm using SDK11 and don't want to migrate to v12, so I wanted to do a workaround...
